# 1/16EM V carve settings **URL:** \ **Category:** Accessories\ **Created:** [February 7, 2021, 3:36pm UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348 "2021-02-07T15:36:46Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![St0mp](https://avatars.discourse-cdn.com/v4/letter/s/ce73a5/32.png) [@St0mp](https://forum.onefinitycnc.com/u/St0mp)\ **Post date:** [February 7, 2021, 3:36pm UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/1 "2021-02-07T15:36:46Z")
I am working on a Makecnc patterns and i think im going to need to use my 1/16th bit to cut out plywood. thickness is about .2 of a inch and smaller. i dont want to brake any bits:) please check my 1/16th settings for this and tell me if they are correct. Please, And Thank you. [bit settings.JPG - Google Drive](https://drive.google.com/file/d/1hkFk2TEd6G4WgeMjp9rVoiKuNwr9bFSJ/view?usp=sharing) ---
**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\ **Post date:** [February 15, 2021, 3:46am UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/2 "2021-02-15T03:46:12Z")
Looks good for most normal bits. DOC = 50% diameter; feed rate seems reasonable. My 0.625 bits have a cut depth of 0.3 or so, so 0.2 should be fine if the bits are similar. -Tom ---
**Author:** ![St0mp](https://avatars.discourse-cdn.com/v4/letter/s/ce73a5/32.png) [@St0mp](https://forum.onefinitycnc.com/u/St0mp)\ **Post date:** [February 15, 2021, 5:19am UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/3 "2021-02-15T05:19:39Z")
do they make a 1/16th compression bit that will cut .20" thick? poplar plywood. I ran them settings on .13" plywood it did fine I thought anyway. but i dont think my 1/16th bit can do max out at .18\*\* I found a long reach bit but i would like a compression bit i think… ---
**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\ **Post date:** [February 15, 2021, 2:29pm UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/4 "2021-02-15T14:29:40Z")
Hi @St0mp - here are a couple I found: > **[\*Astra Coated\* CNC Router Bits - BitsBits.com](https://bitsbits.com/?main_page=product_info&cPath=138_1_16&products_id=124)** > > Your source for \*Astra Coated\* spiral CNC bits, router bits, Whiteside router bits, end mills, engraving tools, Festool power tools and more! > **[(5) 1/16" Carbide End Mills Two Flute .250 LOC \* Made in USA \* CNC M111 | eBay](https://www.ebay.com/itm/5-1-16-Carbide-End-Mills-Two-Flute-250-LOC-Made-in-USA-CNC-M111/162522387971?campid=5338767663&toolid=20012&customid=&mkevt=1&mkcid=1&mkrid=711-53200-19255-0&ufes_redirect=true)** > > Flute Direction:Right Hand (Up Cut). Flute Type:Spiral. Plunge Tip:Square End. Center Cutting?. Cutting Direction:Right Hand. At Drill Bits Unlimited, we are dedicated to providing top quality. the bits long before any significant wear. > **[(5) 1/16" (.0625") CARBIDE END MILL 2 FLUTE KYOCERA 1600.0625.250 | eBay](https://www.ebay.com/itm/5-1-16-0625-CARBIDE-END-MILL-2-FLUTE-KYOCERA-1600-0625-250/381960586630?hash=item58eea00586:g:oQEAAOSwjVVV0Ko1&campid=5338767663&toolid=20012&customid=&mkevt=1&mkcid=1&mkrid=711-53200-19255-0&ufes_redirect=true)** > > These endmills are made by Kyocera Tycom. These tools are normally sold into the printed circuit board market and are made in the USA. You'll not find a better endmill at this price. length of cut. Good luck! -Tom ---
**Author:** ![St0mp](https://avatars.discourse-cdn.com/v4/letter/s/ce73a5/32.png) [@St0mp](https://forum.onefinitycnc.com/u/St0mp)\ **Post date:** [February 15, 2021, 3:42pm UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/5 "2021-02-15T15:42:36Z")
Should i move to a 1/8th collet? here is the bit i am looking at [425-DNC062LR DownCut 2FL Spiral Bit 1/16- w/1/4 LOC & 1/2LOR : Bits & Bits](https://bitsbits.com/index.php?main_page=product_info&cPath=79_161&products_id=1091) was hoping to find in a compression bit though… ---
**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\ **Post date:** [February 22, 2021, 4:06pm UTC](https://forum.onefinitycnc.com/t/1-16em-v-carve-settings/3348/6 "2021-02-22T16:06:30Z")
Hi @St0mp - not sure I’ve seen a 1/16" compression bit (but I’ve never looked for one). I would go with the largest shank you can - it provides more stability and strength. -Tom