# BuildBotics LinuxCNC

**URL:** <https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969>\
**Category:** Firmware (BB Buildbotics) (Discontinued)\
**Created:** [October 25, 2023, 4:16pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969 "2023-10-25T16:16:13Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![tgunr](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/tgunr/32/10947_2.png) [@tgunr](https://forum.onefinitycnc.com/u/tgunr)\
**Post date:** [October 25, 2023, 4:16pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/1 "2023-10-25T16:16:13Z")

</div>

Can anyone tell me or point to some doc that shows which codes are not implemented for the BuildBotics controller?

---

<div class="post-metadata">

**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\
**Post date:** [October 25, 2023, 5:10pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/2 "2023-10-25T17:10:31Z")

</div>

Hey Dave,

you can see those which _ **are** _ implemented on your controller’s user interface at [http://onefinity.local/#cheat-sheet](http://onefinity.local/#cheat-sheet) :

 ![Onefinity_CNC_controler_-_G-Code_Cheat_Sheet](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/d/4/d48301b44782d9694f5d3830f73d40a0f31d0bf6.png)

---

<div class="post-metadata">

**Author:** ![tgunr](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/tgunr/32/10947_2.png) [@tgunr](https://forum.onefinitycnc.com/u/tgunr)\
**Post date:** [October 25, 2023, 5:39pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/3 "2023-10-25T17:39:14Z")

</div>

So G10 L2 is not honored, ☹

---

<div class="post-metadata">

**Author:** ![tgunr](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/tgunr/32/10947_2.png) [@tgunr](https://forum.onefinitycnc.com/u/tgunr)\
**Post date:** [October 25, 2023, 5:42pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/4 "2023-10-25T17:42:45Z")

</div>

I was looking for a way to account for a slight skew of my stock on the spoil board. Shaper Origin has a nice feature where you probe two locations along the. X and one on the Y to set the origin and account for any skew. Looking at the G codes it looks like G10 L2 could be used similarly to rotate around the Z since I can calculate the skew using probing in a similar fashion.

---

<div class="post-metadata">

**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\
**Post date:** [October 25, 2023, 6:19pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/5 "2023-10-25T18:19:51Z")

</div>

> [@tgunr](#):
>
> G10 L2 is not honored, ☹

“G10 L2 (P R)” _ **is** _ mentioned as supported under “Coordinate Systems, Offsets & Planes” on this page.

Remember, the pages on the buildbotics-derived controller are **web pages** so are sort of endless and **need to be scrolled**.

You may also click on “Show unsupported codes” on the bottom of the page

---

<div class="post-metadata">

**Author:** ![tgunr](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/tgunr/32/10947_2.png) [@tgunr](https://forum.onefinitycnc.com/u/tgunr)\
**Post date:** [October 25, 2023, 6:47pm UTC](https://forum.onefinitycnc.com/t/buildbotics-linuxcnc/22969/6 "2023-10-25T18:47:19Z")

</div>

Thanks, I never noticed that!