# Does the Masso controller display the project time remaining (approx) anywhere?

**URL:** <https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038>\
**Category:** Controller (MASSO) Discussion\
**Created:** [June 13, 2023, 3:26am UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038 "2023-06-13T03:26:29Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Captain](https://avatars.discourse-cdn.com/v4/letter/c/f17d59/32.png) [@Captain](https://forum.onefinitycnc.com/u/Captain)\
**Post date:** [June 13, 2023, 3:26am UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/1 "2023-06-13T03:26:29Z")

</div>

While the project is running on the Masso controller, is the time remaining available to view anywhere? I can see the current job time (duration), but not the reverse.

While on this subject, is there a good tutorial on the Masso Controller that anyone can recommend? I’ve looked at some videos and the Masso website, but haven’t seen a thorough, A-Z type guide of the controller with Onefinity yet.

---

<div class="post-metadata">

**Author:** ![ChrisS](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/chriss/32/22864_2.png) [@ChrisS](https://forum.onefinitycnc.com/u/ChrisS)\
**Post date:** [June 14, 2023, 3:55am UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/2 "2023-06-14T03:55:59Z")

</div>

Yes, time and percent… neither are totally accurate. I did a job and it was stuck in the 90% range for more than 10% of the time

Masso site is as good as it gets to my knowledge, but a lot of it is outdated too.

---

<div class="post-metadata">

**Author:** ![Captain](https://avatars.discourse-cdn.com/v4/letter/c/f17d59/32.png) [@Captain](https://forum.onefinitycnc.com/u/Captain)\
**Post date:** [June 14, 2023, 4:03pm UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/3 "2023-06-14T16:03:33Z")

</div>

Where are they located? I dont see either the time remaining or percentage anywhere on my job screen.

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [June 14, 2023, 4:08pm UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/4 "2023-06-14T16:08:05Z")

</div>

It only shows time lapsed and percent done. It does not have a time remaining. If you’d like this feature, send them a request through their page (do not send the request to Onefinity as Masso wouldn’t see it) forum and/or create a ticket with them.

---

<div class="post-metadata">

**Author:** ![ChrisS](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/chriss/32/22864_2.png) [@ChrisS](https://forum.onefinitycnc.com/u/ChrisS)\
**Post date:** [June 14, 2023, 4:42pm UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/5 "2023-06-14T16:42:20Z")

</div>

Thank you, i thought it was time remaining.  
That’s what i get for going off memory when i can’t confirm

---

<div class="post-metadata">

**Author:** ![Wes\_Jac\_79](https://avatars.discourse-cdn.com/v4/letter/w/8797f3/32.png) [@Wes\_Jac\_79](https://forum.onefinitycnc.com/u/Wes_Jac_79)\
**Post date:** [June 19, 2023, 3:57am UTC](https://forum.onefinitycnc.com/t/does-the-masso-controller-display-the-project-time-remaining-approx-anywhere/21038/6 "2023-06-19T03:57:03Z")

</div>

Check out the YouTube channel CNC Nutz. Its run by the Masso forum support person. Lots of helpful videos there.

[CNC Nutz](https://youtube.com/@cncnutzmassoedition9131)