# Dust boot Gen 2 not fitting

**URL:** <https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071>\
**Category:** Onefinity Spindle Kit by Redline CNC\
**Created:** [August 26, 2026, 2:12am UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071 "2026-08-26T02:12:31Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![CMarshall](https://avatars.discourse-cdn.com/v4/letter/c/cc9497/32.png) [@CMarshall](https://forum.onefinitycnc.com/u/CMarshall)\
**Post date:** [August 26, 2026, 2:12am UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/1 "2026-08-26T02:12:31Z")

</div>

The Official Spindle of Onefinity CNC by @Redlinecnc

> **[Redline CNC | CNC Electronics, Spindles, & VFDs, & Controllers](https://www.redlinecnc.com/)**
>
> Redline CNC manufactures high quality CNC parts.
> • Spindles with all metal VFDs
> • Modern CNC Controllers
> “Push your CNC to its limit”

I have the 65mm spindle and the Gen 2 dust boot hits every time I lower the spindle…does anybody else have this issue?

---

<div class="post-metadata">

**Author:** ![evanhawkins04](https://avatars.discourse-cdn.com/v4/letter/e/439d5e/32.png) [@evanhawkins04](https://forum.onefinitycnc.com/u/evanhawkins04)\
**Post date:** [August 26, 2026, 2:25pm UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/2 "2026-08-26T14:25:11Z")

</div>

try lowering your spindle in the holder and slide the dust boot down

---

<div class="post-metadata">

**Author:** ![Oldguy](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/oldguy/32/35832_2.png) [@Oldguy](https://forum.onefinitycnc.com/u/Oldguy)\
**Post date:** [August 26, 2026, 4:18pm UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/3 "2026-08-26T16:18:12Z")

</div>

I had the same issue. I found that when I attached the dust boot I had allowed the end with vacuum hose to lower a couple of mm. That caused it too hit the z axis support. I readjusted the boot and now it clears the support but just barely.

---

<div class="post-metadata">

**Author:** ![CMarshall](https://avatars.discourse-cdn.com/v4/letter/c/cc9497/32.png) [@CMarshall](https://forum.onefinitycnc.com/u/CMarshall)\
**Post date:** [August 29, 2026, 12:22am UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/4 "2026-08-29T00:22:38Z")

</div>

I tried adjusting it every way possible and it hit everytime. Onefinity support said there’s an updated bracket that solves this problem and they’ve shipped it to me. Hopefully it solves this. Thanks for the responses! 🙏

---

<div class="post-metadata">

**Author:** ![Calvin](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/calvin/32/32664_2.png) [@Calvin](https://forum.onefinitycnc.com/u/Calvin)\
**Post date:** [August 29, 2026, 2:04am UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/5 "2026-08-29T02:04:07Z")

</div>

I also had the same but mine was hitting on the 80mm spindle and boot. The new bracket has less material between the linear rails and the spindle.

---

<div class="post-metadata">

**Author:** ![jrhumbleb](https://avatars.discourse-cdn.com/v4/letter/j/a6a055/32.png) [@jrhumbleb](https://forum.onefinitycnc.com/u/jrhumbleb)\
**Post date:** [September 20, 2026, 5:24am UTC](https://forum.onefinitycnc.com/t/dust-boot-gen-2-not-fitting/40071/6 "2026-09-20T05:24:58Z")

</div>

Just got mine this morning it’s doing the same thing …. Did they fix the problem ?
