# Eazy - Z - Elite Tool Setter Issues

**URL:** <https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694>\
**Category:** Troubleshooting (Elite Series)\
**Created:** [June 30, 2024, 12:08pm UTC](https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694 "2024-06-30T12:08:20Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![DonB](https://avatars.discourse-cdn.com/v4/letter/d/9f8e36/32.png) [@DonB](https://forum.onefinitycnc.com/u/DonB)\
**Post date:** [June 30, 2024, 12:08pm UTC](https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694/1 "2024-06-30T12:08:20Z")

</div>

Hello  
First post on this forum. I have the Elite Foreman machine with Eazy Z Tool setter (purchased through Onefinity). Tool setter is mounted on QCW waste board frame.  
I finally got this set up last night and I can get the machine to jog in the X direction directly over tool setter and then it stops. It does not lower down to set the height on the bit.

In Masso controller under Auto tool Zero I have enable auto tool zero, and enable tool setter x position. According to manual I don’t need to enable y tool setter position. I have Z safe distance at -1.000 and tool zero feedrate at 30. This is what is shown on the video and manual from Onefinity. Why is the machine not lowering the Z axis down to set the bit height? Any ideas what I am missing?

Picture below are from manual but basically what I have setup.

![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/6/4/64f984e75b6ac4eef8ebdee736c9e1c37f95fe03.jpeg)

---

<div class="post-metadata">

**Author:** ![Larz](https://avatars.discourse-cdn.com/v4/letter/l/85f322/32.png) [@Larz](https://forum.onefinitycnc.com/u/Larz)\
**Post date:** [June 30, 2024, 3:33pm UTC](https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694/2 "2024-06-30T15:33:11Z")

</div>

I was having what seems to be the same problem. I contacted Onefijity Support and this is what they suggested which did solve my problem.

“ Can you go to the F1 screen and in the center section, scroll down to input 11 (Toolsetter). It should be showing low/green. If it does not, tap the line to highlight it and then press the space bar to change. Once it has changed to low/green, manually depress the toolsetter and watching the screen at input 11. When you depress the toolsetter, do you see it change from low/green to high/red?”

---

<div class="post-metadata">

**Author:** ![DonB](https://avatars.discourse-cdn.com/v4/letter/d/9f8e36/32.png) [@DonB](https://forum.onefinitycnc.com/u/DonB)\
**Post date:** [June 30, 2024, 5:01pm UTC](https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694/3 "2024-06-30T17:01:37Z")

</div>

Thank You!!!  
It was set to high. Changed it to low(green) hit the homing button and it worked like a champ.

I spent 3 hours last night trying to figure this out. Figured it would be a support ticket to Onefinity.  
This is new to me and I am sure I have a long journey ahead. Should be fun.

---

<div class="post-metadata">

**Author:** ![DonB](https://avatars.discourse-cdn.com/v4/letter/d/9f8e36/32.png) [@DonB](https://forum.onefinitycnc.com/u/DonB)\
**Post date:** [June 30, 2024, 5:05pm UTC](https://forum.onefinitycnc.com/t/eazy-z-elite-tool-setter-issues/27694/4 "2024-06-30T17:05:39Z")

</div>

Now I see the link that had the information.

[https://forum.onefinitycnc.com/t/tool-setter-elite-masso-settings-faq/25461](https://forum.onefinitycnc.com/t/tool-setter-elite-masso-settings-faq/25461)