# Ellipse no circle

**URL:** <https://forum.onefinitycnc.com/t/ellipse-no-circle/11309>\
**Category:** Troubleshooting (X35/X50)\
**Created:** [February 19, 2022, 12:25am UTC](https://forum.onefinitycnc.com/t/ellipse-no-circle/11309 "2022-02-19T00:25:47Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Destino](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/destino/32/4336_2.png) [@Destino](https://forum.onefinitycnc.com/u/Destino)\
**Post date:** [February 19, 2022, 12:25am UTC](https://forum.onefinitycnc.com/t/ellipse-no-circle/11309/1 "2022-02-19T00:25:47Z")

</div>

Hello everyone.

I just did my first test with the Journeyman.

Draw a circle and some texts in Aspire. Update the Onefinity firmware, in Aspire install the drivers that the forum indicated for this software. But when executing the programs, the circle turned ellise with its longest axis in X and the texts equally wider.

Any idea what I did wrong?

---

<div class="post-metadata">

**Author:** ![WaywardWoodworker](https://avatars.discourse-cdn.com/v4/letter/w/e79b87/32.png) [@WaywardWoodworker](https://forum.onefinitycnc.com/u/WaywardWoodworker)\
**Post date:** [February 19, 2022, 12:57am UTC](https://forum.onefinitycnc.com/t/ellipse-no-circle/11309/2 "2022-02-19T00:57:16Z")

</div>

Take a look at this link, it shows how to update the settings for the X axis and ensure the travel-per-rev and soft limits are set appropriately for the journeyman.

> [@Proper Motor Settings for x-50 rails (Woodworker and Journeyman), with 1616 ball screw configuration](https://forum.onefinitycnc.com/t/proper-motor-settings-for-x-50-rails-woodworker-and-journeyman-with-1616-ball-screw-configuration/7152):
>
> UPDATE: With the release of 1.0.9 firmware, these settings are now part of the default configuartion. Ensure you are on 1.0.9 firmware ([https://forum.onefinitycnc.com/t/firmware-update-1-0-9-12-17-21-latest-release/84830](https://forum.onefinitycnc.com/t/firmware-update-1-0-9-12-17-21-latest-release/84830)) or later and then reset the configuration, choosing your correct machine configuration: [How To Reset The Configuration To Defaults](https://forum.onefinitycnc.com/t/how-to-reset-the-configuration-to-defaults/2547) (OLD) These settings only apply to X-50 Woodworker and Journeyman with the 1616 ballscrew configuration. Please note: these settings are in M…

---

<div class="post-metadata">

**Author:** ![Destino](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/destino/32/4336_2.png) [@Destino](https://forum.onefinitycnc.com/u/Destino)\
**Post date:** [February 19, 2022, 8:59pm UTC](https://forum.onefinitycnc.com/t/ellipse-no-circle/11309/3 "2022-02-19T20:59:30Z")

</div>

Problem result. Thanks Derek