# Gen2/Redline HMI and RapidChange **URL:** \ **Category:** Gen 2 Elite Series\ **Created:** [February 17, 2026, 5:01am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497 "2026-02-17T05:01:39Z")\ **Posts on this page:** 9\ **Page:** 1
**Author:** ![smgvbest](https://avatars.discourse-cdn.com/v4/letter/s/90db22/32.png) [@smgvbest](https://forum.onefinitycnc.com/u/smgvbest)\ **Post date:** [February 17, 2026, 5:01am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/1 "2026-02-17T05:01:40Z")
I’ve searched and maybe my googlefu is just not up to the task. Will the Gen2/Redline HMI support 1 or 2 ATC’s? 4 tool holders is not really enough 8, it better also, can the Redline Controller work with the RapidATC from the vendor themselves or is it only compatible wih the ATC sold here? ---
**Author:** ![L.M](https://avatars.discourse-cdn.com/v4/letter/l/a87d85/32.png) [@L.M](https://forum.onefinitycnc.com/u/L.M)\ **Post date:** [February 17, 2026, 1:11pm UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/2 "2026-02-17T13:11:14Z")
Based on the Redline interface there appear to be support for up to 4 ATC’s with a total of 16 tools. If you look in the bottom section of the screen shot you’ll see ATC 1-4 used for assigning which tool number is located in which slot of the indicated ATC: ![Screenshot 2026-02-17 at 08.05.27](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/c/e/ce6944b4a997ca5038641bf5c3bd08670c2fef38.png) The only caveat to this, I believe, is that if you’re using a QCW table with a QCW adapter (ATC mounts on the front of the QCW table) it will only accommodate one ATC configured that way. More than one ATC require that you table mount your ATC’s. I’m not 100% certain on this, while I have the ATC and a QCW I’m waiting for the software to complete development to allow ATC configuration / use. ---
**Author:** ![smgvbest](https://avatars.discourse-cdn.com/v4/letter/s/90db22/32.png) [@smgvbest](https://forum.onefinitycnc.com/u/smgvbest)\ **Post date:** [February 18, 2026, 8:39am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/3 "2026-02-18T08:39:27Z")
That’s good to see, I’ll dive more into the manual. I mostly work with MDF and Acrylic for Flight Sim Cockpits so having all the tools available really helps my workflow, that said I’m going from 0 ATC to 4 Tools but 8 would be better for my needs ---
**Author:** ![L.M](https://avatars.discourse-cdn.com/v4/letter/l/a87d85/32.png) [@L.M](https://forum.onefinitycnc.com/u/L.M)\ **Post date:** [February 18, 2026, 10:48am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/4 "2026-02-18T10:48:38Z")
Flight sim cockpits? That’s fascinating. If you’re able, I hope you post some pictures of your work once you get everything running. I’d love to see it. Cheers. ---
**Author:** ![smgvbest](https://avatars.discourse-cdn.com/v4/letter/s/90db22/32.png) [@smgvbest](https://forum.onefinitycnc.com/u/smgvbest)\ **Post date:** [March 1, 2026, 7:57am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/5 "2026-03-01T07:57:29Z")
Sure, ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/b/7/b772438a1998ec49de61867d36770378aeaf32e8.jpeg) ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/0/1/017ceb00165677951ab9b9fc5814e4312d4e823f.jpeg) ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/a/b/aba43430fbc84931d0a8c954a8a6710cb2d42b60.jpeg) ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/b/0/b09d3aca380830e8e23b4c87a242c78a64a61503.jpeg) right now these panels are 3 part, a backplate, light plate and legend plate. I want to do them the way real ones are done which have the light plate and legend plate are 1 peice, but to do so you have 2 different holes, front side is the smaller and the back side has a larger hole to allow the switch/pot nut to be recessed a little but the larger white ring s/b clear to allow light thru to illuminate the knobs indica. i need a CNC to do that, can’t do on a laser, hence my move to the Onefinity. getting the Foreman to also allow me to make the MDF frame parts I do run a etsy store selling these parts this is my own build (a WIP) ![IMG_0832](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/7/4/74ec250ed35f884c38f9dbd1c67680d455ef1d9f.jpeg) ---
**Author:** ![L.M](https://avatars.discourse-cdn.com/v4/letter/l/a87d85/32.png) [@L.M](https://forum.onefinitycnc.com/u/L.M)\ **Post date:** [March 1, 2026, 1:52pm UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/6 "2026-03-01T13:52:23Z")
Just, WOW, beautiful work. 🙂 ---
**Author:** ![JimHatch](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/jimhatch/32/3928_2.png) [@JimHatch](https://forum.onefinitycnc.com/u/JimHatch)\ **Post date:** [March 1, 2026, 2:25pm UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/7 "2026-03-01T14:25:33Z")
> [@smgvbest](#): > > i need a CNC to do that, can’t do on a laser, hence my move to the Onefinity You should check out the Glowforge laser forum. There a doctor from Boston doing the full cockpit for an Airbus I think using his laser. He just finished up the pilot’s emergency oxygen face mask and face shield. ---
**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\ **Post date:** [March 5, 2026, 9:13pm UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/8 "2026-03-05T21:13:08Z")
This is an EPIC build! Love it! ---
**Author:** ![smgvbest](https://avatars.discourse-cdn.com/v4/letter/s/90db22/32.png) [@smgvbest](https://forum.onefinitycnc.com/u/smgvbest)\ **Post date:** [March 15, 2026, 5:21am UTC](https://forum.onefinitycnc.com/t/gen2-redline-hmi-and-rapidchange/37497/9 "2026-03-15T05:21:25Z")
I’m in batch 4 for my Gen2 and can’t wait to work on our type b panels which are virtually identical to real panels patiently waiting for batch4 😃