# Help with gcode and skipped steps (solved, max deviation)

**URL:** <https://forum.onefinitycnc.com/t/help-with-gcode-and-skipped-steps-solved-max-deviation/20324>\
**Category:** Uncategorized\
**Created:** [April 28, 2023, 6:34am UTC](https://forum.onefinitycnc.com/t/help-with-gcode-and-skipped-steps-solved-max-deviation/20324 "2023-04-28T06:34:40Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![UltraPeepi](https://avatars.discourse-cdn.com/v4/letter/u/fbc32d/32.png) [@UltraPeepi](https://forum.onefinitycnc.com/u/UltraPeepi)\
**Post date:** [April 28, 2023, 6:34am UTC](https://forum.onefinitycnc.com/t/help-with-gcode-and-skipped-steps-solved-max-deviation/20324/1 "2023-04-28T06:34:40Z")

</div>

I have a little carve that takes 2 minutes. It’s two circular pockets, and a profile. One of the pockets causes skips unless I slow the feed rate down significantly. I am trying to debug the problem. I have eliminated nearly ALL of the gcode and trimmed it down to just a portion of the pocket that causes skips.

Note: this is an air carve - the router isn’t on, and Z is well above the axis.

The following skips every time toward the end. Am I missing something?

G21  
G17G90  
S18000M03

G0X0Y0Z15  
X133.586Y27.713  
G1Z10F1500

X141.158Y25.03F3000

M0

X142.025Y27.125  
X142.137Y28.258  
X142.025Y29.392  
X141.695Y30.481  
X141.158Y31.486  
X140.435Y32.366  
X139.555Y33.089  
X138.551Y33.626  
X137.461Y33.956  
X136.327Y34.068  
X135.194Y33.956  
X134.104Y33.626  
X133.1Y33.089  
X132.219Y32.366  
X131.497Y31.486  
X130.96Y30.481  
X130.629Y29.392  
X130.518Y28.258  
X130.629Y27.125  
G0Z15

---

<div class="post-metadata">

**Author:** ![Enginerd](https://avatars.discourse-cdn.com/v4/letter/e/bcef8e/32.png) [@Enginerd](https://forum.onefinitycnc.com/u/Enginerd)\
**Post date:** [April 28, 2023, 11:07am UTC](https://forum.onefinitycnc.com/t/help-with-gcode-and-skipped-steps-solved-max-deviation/20324/2 "2023-04-28T11:07:17Z")

</div>

The format looks correct but I notced a few places where the number of decimal places change. It looks like it starts with 3 decimal places but there are lines with one or two. You might try adding the zeros to make them all three.

---

<div class="post-metadata">

**Author:** ![UltraPeepi](https://avatars.discourse-cdn.com/v4/letter/u/fbc32d/32.png) [@UltraPeepi](https://forum.onefinitycnc.com/u/UltraPeepi)\
**Post date:** [April 28, 2023, 6:19pm UTC](https://forum.onefinitycnc.com/t/help-with-gcode-and-skipped-steps-solved-max-deviation/20324/3 "2023-04-28T18:19:44Z")

</div>

Problem solved. My max-deviation was set to 0.05mm. I changed it to 0.1mm and no more skips. 🙂
