# Homing alarm problem

**URL:** <https://forum.onefinitycnc.com/t/homing-alarm-problem/28565>\
**Category:** Troubleshooting (Elite Series)\
**Created:** [September 9, 2024, 2:45pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565 "2024-09-09T14:45:52Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Richie](https://avatars.discourse-cdn.com/v4/letter/r/d6d6ee/32.png) [@Richie](https://forum.onefinitycnc.com/u/Richie)\
**Post date:** [September 9, 2024, 2:45pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/1 "2024-09-09T14:45:52Z")

</div>

I have a elite journeyman with masso 3. Ive been getting a homing alarm at power up. I power up and release the estop and press the homing buttob twice and the z goes down about a half inch then stops and masso shown a homing alarm. How did this happen and how do i fix it?

---

<div class="post-metadata">

**Author:** ![TMToronto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@TMToronto](https://forum.onefinitycnc.com/u/TMToronto)\
**Post date:** [September 9, 2024, 3:16pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/2 "2024-09-09T15:16:11Z")

</div>

The Z axis should raise to the highest position when homing.

In the homing screen/settings, if you have “Request homing on startup/after estop checked” uncheck them save and restart controller (you can check them again later after troubleshooting).

After restart, use the jog commands to move the Z axis … does Z+ move the spindle up or down?

---

<div class="post-metadata">

**Author:** ![Richie](https://avatars.discourse-cdn.com/v4/letter/r/d6d6ee/32.png) [@Richie](https://forum.onefinitycnc.com/u/Richie)\
**Post date:** [September 9, 2024, 4:42pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/3 "2024-09-09T16:42:46Z")

</div>

Tried this and but still can not move jog command. Also rechecked the homing after estop and after releasing the estop this time i get an x motor alarm. Checked the motors and nothing out of order there. I am so confused. This was all going good last week.

---

<div class="post-metadata">

**Author:** ![TMToronto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@TMToronto](https://forum.onefinitycnc.com/u/TMToronto)\
**Post date:** [September 9, 2024, 4:54pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/4 "2024-09-09T16:54:23Z")

</div>

When jogging you are set on continuous mode?

I would not worry about homing until you get your 3 axes to move as expected.

It sounds like this is a new issue - I thought initially this was a new install.

If you did not change any settings, perhaps double check all wiring and connectors and try again to jog axes - no homing yet.

There will be a solution.

---

<div class="post-metadata">

**Author:** ![Richie](https://avatars.discourse-cdn.com/v4/letter/r/d6d6ee/32.png) [@Richie](https://forum.onefinitycnc.com/u/Richie)\
**Post date:** [September 9, 2024, 5:36pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/5 "2024-09-09T17:36:54Z")

</div>

Ifound that the rowdy roman hose system had a bent limit switch connection so never shut the x axiis. Once i corrected this all worked fine. Thank you for your help.

---

<div class="post-metadata">

**Author:** ![TMToronto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@TMToronto](https://forum.onefinitycnc.com/u/TMToronto)\
**Post date:** [September 9, 2024, 7:01pm UTC](https://forum.onefinitycnc.com/t/homing-alarm-problem/28565/6 "2024-09-09T19:01:42Z")

</div>

You are welcome - great sleuthing on your part - and happy you are up and running again.
