# Machine cutting, everything stops. Resets X,Y,Z to zero and says the machine in not homed **URL:** \ **Category:** Uncategorized\ **Created:** [February 25, 2023, 6:30pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030 "2023-02-25T18:30:15Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![dnelson](https://avatars.discourse-cdn.com/v4/letter/d/3d9bf3/32.png) [@dnelson](https://forum.onefinitycnc.com/u/dnelson)\ **Post date:** [February 25, 2023, 6:30pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/1 "2023-02-25T18:30:15Z")
Everything worked ok yesterday. Doing the same cut today. Started the machine, homed the machine. Set up the project and started carving. Part way through the second pass in the pocket the machine stopped, (router still running) machine reset X,Y,Z to zero and showed on the screen not homed. Tried a second time, almost same spot the machine did it again. Any thoughts ---
**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\ **Post date:** [February 25, 2023, 6:43pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/2 "2023-02-25T18:43:00Z")
Hey dnelson, - [Troubleshooting: Rail is getting hung, stuck, or out of alignment](https://forum.onefinitycnc.com/t/troubleshooting-rail-is-getting-hung-stuck-or-out-of-alignment/10826) I would check all points one by one to see why your carriage does not move anymore in the middle of the axis. Furthermore, should your machine not be properly [rectangular (“squared”)](https://forum.onefinitycnc.com/t/what-do-i-do-first/18349/6), the Y movement can block. ---
**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\ **Post date:** [February 25, 2023, 7:23pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/3 "2023-02-25T19:23:09Z")
What firmware version are you on? ---
**Author:** ![dnelson](https://avatars.discourse-cdn.com/v4/letter/d/3d9bf3/32.png) [@dnelson](https://forum.onefinitycnc.com/u/dnelson)\ **Post date:** [February 25, 2023, 9:28pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/4 "2023-02-25T21:28:26Z")
> OnefinityCNC [1] Onefinity Support Leader > February 25 > > Good afternoon, > I’m using 10.504. I shut everything down, unplugged everything. > Plugged everything back in, used a new thumb drive and made three cuts > and so far everything is working as it should. I had mad a 2.5 hour cut > yesterday with no issues. Thanks for the reply. Will let you know if I have any other issues. Daryl What firmware version are you on? ---
**Author:** ![dnelson](https://avatars.discourse-cdn.com/v4/letter/d/3d9bf3/32.png) [@dnelson](https://forum.onefinitycnc.com/u/dnelson)\ **Post date:** [February 25, 2023, 9:34pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/5 "2023-02-25T21:34:02Z")
Well, don’t know what the issue was. Shut everything down, unplugged everything and plugged everything back in. Loaded the program onto a new thumb drive, ran the program for 3 cuts and no issues. So far the problem has corrected itself. Don’t know what caused it but so far everything is running as it should. running 10.504 ---
**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\ **Post date:** [February 25, 2023, 9:43pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/6 "2023-02-25T21:43:59Z")
Hey Daryl, > [@dnelson](#): > > running 10.504 I think @onefinitycnc meant the Onefinity Controller firmware version, not the Vectric version 🙂 ---
**Author:** ![dnelson](https://avatars.discourse-cdn.com/v4/letter/d/3d9bf3/32.png) [@dnelson](https://forum.onefinitycnc.com/u/dnelson)\ **Post date:** [February 25, 2023, 9:53pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/7 "2023-02-25T21:53:40Z")
Right you are. 1.0.9 is the firmware. ---
**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\ **Post date:** [February 25, 2023, 11:26pm UTC](https://forum.onefinitycnc.com/t/machine-cutting-everything-stops-resets-x-y-z-to-zero-and-says-the-machine-in-not-homed/19030/8 "2023-02-25T23:26:10Z")
Sounds like EMI if that’s the case. [https://forum.onefinitycnc.com/search?q=emi](https://forum.onefinitycnc.com/search?q=emi)