# Magnetic Replacement for Suckit Router Shield - Now Available

**URL:** <https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867>\
**Category:** Suck It Dust Boot\
**Created:** [December 29, 2021, 12:32am UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867 "2021-12-29T00:32:28Z")\
**Posts on this page:** 10\
**Page:** 1

<div class="post-metadata">

**Author:** ![TheyCallMeJohn](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/theycallmejohn/32/7657_2.png) [@TheyCallMeJohn](https://forum.onefinitycnc.com/u/TheyCallMeJohn)\
**Post date:** [December 29, 2021, 12:32am UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/1 "2021-12-29T00:32:28Z")

</div>

Tired of shattered dust shields? Tired of having a plate that isn’t the right size for optimal dust control. Well look no further.

This is a a set of Magnetic Quick Swap Plates. Include four pieces, the base plate and three smaller magnetic swap plates.

The base plate is designed to accommodate flattening bits with the smaller plates in the following size to accommodate all your bits protection needs.

The diameters are as follows:

Main Plate: 45 mm -1.77 in  
Large Plate: 35 mm - 1.38 in  
Medium Plate: 25 mm 0.98 in  
Small Plate: 11 mm 0.43 in

Also these plates are not made of acrylic like the original rather, polycarbonate/Lexan this plastic is extremely impact resistant so if your bit hits the plate you will likely have small chip rather than shattered plate.

Note: Display stand shown in picture is not include.

Here is a coupon code that will be valid for the next week: HBMAGLAUNCH10

> **[Magnetic Quick Swap Plates for Suckit Dust Shoe/router Shield - Etsy](https://www.etsy.com/HuntingtonBuilds/listing/1145189343/magnetic-quick-swap-plates-for-suckit?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1640737884342)**
>
> This Tools item by HuntingtonBuilds has 69 favorites from Etsy shoppers. Ships from Huntington Beach, CA. Listed on Nov 10, 2022

Follow my Instagram for more Onefinity accessories. @huntingtonbuilds

---

<div class="post-metadata">

**Author:** ![RowdyRoman](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/rowdyroman/32/14_2.png) [@RowdyRoman](https://forum.onefinitycnc.com/u/RowdyRoman)\
**Post date:** [December 29, 2021, 6:03pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/2 "2021-12-29T18:03:47Z")

</div>

John these are awesome and well made! Thanks for letting me test them out! I have had zero problems over the past several months!!

---

<div class="post-metadata">

**Author:** ![TheyCallMeJohn](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/theycallmejohn/32/7657_2.png) [@TheyCallMeJohn](https://forum.onefinitycnc.com/u/TheyCallMeJohn)\
**Post date:** [December 29, 2021, 6:08pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/3 "2021-12-29T18:08:31Z")

</div>

Peter, thanks for the help and the feedback.

---

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [December 29, 2021, 8:13pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/4 "2021-12-29T20:13:09Z")

</div>

Hi John -these look great; on my way to purchasing but the coupon code does not seem to be working for me. Can you check?

> [@TheyCallMeJohn](#):
>
> HBMAGLAUNCH10

-Tom

---

<div class="post-metadata">

**Author:** ![TheyCallMeJohn](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/theycallmejohn/32/7657_2.png) [@TheyCallMeJohn](https://forum.onefinitycnc.com/u/TheyCallMeJohn)\
**Post date:** [December 29, 2021, 9:16pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/5 "2021-12-29T21:16:05Z")

</div>

> [@TheyCallMeJohn](#):
>
> HBMAGLAUNCH10

Tom,  
That looks the same as what I have on my end. I just tested it thru my personal account and it seemed to work. Make sure you are putting it under “Shop Coupon Codes” instead of “Etsy Coupon Codes”. I have made that mistake a couple times. The link below should also plug it in as well. Please let me know if that doesn’t resolve it. Appreciate the support!

 ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/2X/c/ca3fe60ea7b697c39211d916c67353c776348921.png)

[https://www.etsy.com/shop/HuntingtonBuilds?coupon=HBMAGLAUNCH10](https://www.etsy.com/shop/HuntingtonBuilds?coupon=HBMAGLAUNCH10)

---

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [December 29, 2021, 9:46pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/6 "2021-12-29T21:46:08Z")

</div>

> [@TheyCallMeJohn](#):
>
> he same as what I have on my end. I just tested it thru my personal account and it seemed to work. Make sure you are putting it under “Shop Coupon Codes” instead of “Etsy Coupon Codes”. I have made that mistake a couple times. The link below should also pl

Ah, many thanks. I was definitely using the Etsy code. Excellent work!

---

<div class="post-metadata">

**Author:** ![TheyCallMeJohn](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/theycallmejohn/32/7657_2.png) [@TheyCallMeJohn](https://forum.onefinitycnc.com/u/TheyCallMeJohn)\
**Post date:** [December 29, 2021, 9:51pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/7 "2021-12-29T21:51:36Z")

</div>

Thank you for order, can’t wait for you to try it out!

---

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [December 29, 2021, 9:53pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/8 "2021-12-29T21:53:46Z")

</div>

Thanks John - I destroyed the smaller one and now chips are flying everywhere with the big one. Happy to support cool tools by makers!

---

<div class="post-metadata">

**Author:** ![TheyCallMeJohn](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/theycallmejohn/32/7657_2.png) [@TheyCallMeJohn](https://forum.onefinitycnc.com/u/TheyCallMeJohn)\
**Post date:** [January 31, 2022, 4:52pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/9 "2022-01-31T16:52:03Z")

</div>

Just wanted to share this video Tom, The Guru, @cyberreefguru put out yesterday.

[![](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/d/c/dc125bf31cbafb379ac250b5517a53550775a321.jpeg "Boost your CNC dust collection! (Coupon Code Included)") ](https://www.youtube.com/watch?v=8Ova4WQWLuM)

---

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [January 31, 2022, 5:05pm UTC](https://forum.onefinitycnc.com/t/magnetic-replacement-for-suckit-router-shield-now-available/9867/10 "2022-01-31T17:05:25Z")

</div>

Thanks John!

Don’t forget the coupon code in the description 🙂
