# New bug (for me, at least) **URL:** \ **Category:** Uncategorized\ **Created:** [January 21, 2022, 1:12am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547 "2022-01-21T01:12:05Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![ConvenientWoodwork](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/convenientwoodwork/32/22558_2.png) [@ConvenientWoodwork](https://forum.onefinitycnc.com/u/ConvenientWoodwork)\ **Post date:** [January 21, 2022, 1:12am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/1 "2022-01-21T01:12:05Z")
I am performing an engrave operation but I have my Z set slightly above the work just so I can verify everything is lined up. The router is off, and I press play to begin the program. After a couple seconds I pause to verify alignment and everything looks good. I hit play and the router goes off sideways (thankfully not down!). The controller has put itself in “jogging” mode and is no longer following the gcode. I am unable to jog using the on-screen buttons or the controller, nor will it home. I press the on-screen e-stop and then clear it and the motors now read “shutdown”. Reboot the controller a couple of times and things finally go back to normal. ---
**Author:** ![AndyP](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/andyp/32/1106_2.png) [@AndyP](https://forum.onefinitycnc.com/u/AndyP)\ **Post date:** [January 21, 2022, 9:36am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/2 "2022-01-21T09:36:38Z")
I think similar has happened to me a couple of times but appeared random and unrepeatable (well I can’t really remember the sequence of events in detail) and I didn’t have time to investigate I was just pleased I could get it back to an operable state. ---
**Author:** ![ConvenientWoodwork](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/convenientwoodwork/32/22558_2.png) [@ConvenientWoodwork](https://forum.onefinitycnc.com/u/ConvenientWoodwork)\ **Post date:** [January 21, 2022, 2:04pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/3 "2022-01-21T14:04:07Z")
This is the second time I’ve had the motors “shutdown” during what was otherwise normal operation, but the first time it went into “jogging” mode in the middle of a program. ---
**Author:** ![robbe](https://avatars.discourse-cdn.com/v4/letter/r/df788c/32.png) [@robbe](https://forum.onefinitycnc.com/u/robbe)\ **Post date:** [January 21, 2022, 8:47pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/4 "2022-01-21T20:47:56Z")
Bumping this up. Unfortunately I did not pay attention to what led to this. I had the situation that the on-screen display was stuck in “Jogging” and the only solution I found was rebooting. That was a bummer because I had set the workpiece zero and was between runs. I was able to reposition by noting down the X/Y/Z and then after reboot using the MDI to set the former zero precisely (by moving -X-Y-Z, then zeroing). ---
**Author:** ![ConvenientWoodwork](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/convenientwoodwork/32/22558_2.png) [@ConvenientWoodwork](https://forum.onefinitycnc.com/u/ConvenientWoodwork)\ **Post date:** [January 21, 2022, 10:54pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/5 "2022-01-21T22:54:47Z")
@davidsmith had a similar issue a few days ago. His thread is [here](https://forum.onefinitycnc.com/t/when-i-start-my-machine/10404) ---
**Author:** ![davidsmith](https://avatars.discourse-cdn.com/v4/letter/d/c57346/32.png) [@davidsmith](https://forum.onefinitycnc.com/u/davidsmith)\ **Post date:** [January 22, 2022, 4:10am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/6 "2022-01-22T04:10:35Z")
Hey Nick Onefinity sent me a new controller and I am up and running again Thanks again Seems like it was something internal and my machine was just purchased Super happy with the machine and the support Great company off to a great start ---
**Author:** ![clhuggins](https://avatars.discourse-cdn.com/v4/letter/c/53a042/32.png) [@clhuggins](https://forum.onefinitycnc.com/u/clhuggins)\ **Post date:** [January 26, 2022, 1:39am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/7 "2022-01-26T01:39:14Z")
Yes, frustrating in the middle of a 3+ tool change, and I’ve got to scrap the pieces cause I can’t perfectly re-zero. I’ve tried taking a pic of the zero positions, and then attempting to land on them again, but it’s not been perfect with precise things like chamfers needing to hit the previous milling. ---
**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\ **Post date:** [January 26, 2022, 2:34pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/8 "2022-01-26T14:34:05Z")
You must be deliberate in waiting a few seconds when touching play/pause/stop. It takes a few seconds to ‘clear’ inside the controller. If you do them to quickly, the controller thinks you’re trying to do a command while it’s already executing a command. ---
**Author:** ![ConvenientWoodwork](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/convenientwoodwork/32/22558_2.png) [@ConvenientWoodwork](https://forum.onefinitycnc.com/u/ConvenientWoodwork)\ **Post date:** [January 26, 2022, 4:28pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/9 "2022-01-26T16:28:01Z")
Thanks for the clarification. I have submitted a stepping feature request. ---
**Author:** ![lflaharty](https://avatars.discourse-cdn.com/v4/letter/l/ecae2f/32.png) [@lflaharty](https://forum.onefinitycnc.com/u/lflaharty)\ **Post date:** [August 24, 2022, 4:10am UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/10 "2022-08-24T04:10:23Z")
This is exactly how it happens to me. I fat finger the play button and hit it twice. The controller ends up in “jogging mode” and the only thing I can do to get out is reboot. ---
**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\ **Post date:** [October 2, 2022, 11:22pm UTC](https://forum.onefinitycnc.com/t/new-bug-for-me-at-least/10547/11 "2022-10-02T23:22:42Z")
Just had this happen to me. It would be nice to have some sort of reset option without losing the current zero location. I can still move with the gamepad but not from the screen. -Tom