# Odd Z axis problem

**URL:** <https://forum.onefinitycnc.com/t/odd-z-axis-problem/27010>\
**Category:** Elite Series (Masso & Redline) (Gen 1)\
**Created:** [May 14, 2024, 4:29am UTC](https://forum.onefinitycnc.com/t/odd-z-axis-problem/27010 "2024-05-14T04:29:48Z")\
**Posts on this page:** 1\
**Showing post:** 4

<div class="post-metadata">

**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\
**Post date:** [May 14, 2024, 1:40pm UTC](https://forum.onefinitycnc.com/t/odd-z-axis-problem/27010/4 "2024-05-14T13:40:34Z")

</div>

Hey cvcolomb,

just to be sure, if it’s your first ER collet, do you know that they are not mounted the same way as router collets?

[![ER_collet_Excentric_Extractor_Ring_-Offset_Lip-_Haas_Automation](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/f/6/f6c2544e0ea9ad9586d32abb4c0a70c396b01b6f.png)  
ER Collet Essentials. Do You Know? – Haas Automation Tip of the Day - Youtube ](https://youtu.be/WKikm6cQKh0?t=778)

The link jumps to the moment in the video where it is shown.

> [@Flatttening wasteboard going badly, foreman gone too deep](https://forum.onefinitycnc.com/t/flatttening-wasteboard-going-badly-foreman-gone-too-deep/21261/3):
>
> Also is it possible that you made a mistake when mounting the collet?
> 
> **[ER collets](https://forum.onefinitycnc.com/t/metric-collets-for-makita/18428#the-er-collet-1) are not mounted the way a trim router collet is mounted.** Most people put the collet into the axle of the spindle and then they put the collet nut over it. **That is definetely wrong!** An ER collet has a groove that goes all the way around near the top of the collet. The corresponding **collet nut** of an ER collet has an excentric extractor ring or offset lip inside. It is absolutely mandatory to fully engage (clip in) the collet inside the nut **before** you tighten it onto the holder, as shown at [this moment of the video “ER Collets | 5 Things to Know for Beginners”](https://www.youtube.com/watch?v=R0tJorTM0BE&t=153s). See also this picture from my spindle manual:
> 
> ![Mechatron__Installing_Collet_into_Nut](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/6/1/61594bd2483e75da373dc60176160f9ec009bc77.png)
> 
> – Source: Mechatron HFS Spindle User’s Manual
> 
> [![ER_collet__Excentric_Extractor_Ring_-Offset_Lip-_SS_Workshop](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/2X/a/ac7f0864fd297dd32b88c7c2c94cff54c6033045.jpeg)  
> ER Collets | 5 Things to Know for Beginners - Youtube ](https://www.youtube.com/watch?v=R0tJorTM0BE&t=153s)
> 
> [![ER_collet_Excentric_Extractor_Ring_-Offset_Lip-_Haas_Automation](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/f/6/f6c2544e0ea9ad9586d32abb4c0a70c396b01b6f.png)  
> ER Collet Essentials. Do You Know? – Haas Automation Tip of the Day - Youtube ](https://youtu.be/WKikm6cQKh0?t=778)
> 
> The link jumps to the moment in the video where it is shown.

---

_[View the full topic](https://forum.onefinitycnc.com/t/odd-z-axis-problem/27010)._
