# Onefinity foot bolt size / table / anti-torsion box **URL:** \ **Category:** Uncategorized\ **Created:** [October 20, 2024, 10:13pm UTC](https://forum.onefinitycnc.com/t/onefinity-foot-bolt-size-table-anti-torsion-box/29031 "2024-10-20T22:13:20Z")\ **Posts on this page:** 4\ **Page:** 1
**Author:** ![Okie1](https://avatars.discourse-cdn.com/v4/letter/o/b5e925/32.png) [@Okie1](https://forum.onefinitycnc.com/u/Okie1)\ **Post date:** [October 20, 2024, 10:13pm UTC](https://forum.onefinitycnc.com/t/onefinity-foot-bolt-size-table-anti-torsion-box/29031/1 "2024-10-20T22:13:20Z")
Hi, I’m drawing a print to have a table built to mount a Foreman model machine. I need the mounting bolt size for the machine mounts on the 4 corners of the machine. Any help would be appreciated. Thanks, Mike ---
**Author:** ![TMToronto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@TMToronto](https://forum.onefinitycnc.com/u/TMToronto)\ **Post date:** [October 20, 2024, 11:45pm UTC](https://forum.onefinitycnc.com/t/onefinity-foot-bolt-size-table-anti-torsion-box/29031/2 "2024-10-20T23:45:16Z")
[https://forum.onefinitycnc.com/t/common-bolt-screw-types-on-the-onefinity/3057](https://forum.onefinitycnc.com/t/common-bolt-screw-types-on-the-onefinity/3057) ---
**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\ **Post date:** [October 21, 2024, 6:29am UTC](https://forum.onefinitycnc.com/t/onefinity-foot-bolt-size-table-anti-torsion-box/29031/3 "2024-10-21T06:29:27Z")
Hey Mike, > [@Swelling issues, Table](https://forum.onefinitycnc.com/t/swelling-issues-table/17642/12): > > with the Onefinity machine, for attaching the feet, you just get wood screws ([packing list](https://forum.onefinitycnc.com/t/packing-list-for-the-onefinity-woodworker/3580)) but I would not use such screws. I would use [bolts](https://en.wikipedia.org/wiki/Bolt_(fastener)) matching the corresponding diameter in the feet, possibly with a matching sleeve. This drawing from Bill @Machinist will help you: > > > [@Woodworker Foot Profile](https://forum.onefinitycnc.com/t/woodworker-foot-profile/9915/7): > > > > Unfortunately I did not find the time to make these measurements yet, but Bill @Machinist makes very nice plans, on this one, there wasn’t much that was missing and that he would have measured the holes of the rails. Perhaps he has a plan of the whole foot cross section? > > > > > [@](#): > > > > > > Here’s a document I created for my Machinist, and you just add 16" for the Woodworker. These dimensions worked perfectly for my base. [MACHINIST FOOTPRINT.pdf](https://forum.onefinitycnc.com/uploads/short-url/6KD0qIcwTq1YgKCIdzNXRAd4fz1.pdf) (51.7 KB) > > > > Thank Bill @Machinist for this > > > > ![MACHINIST_FOOTPRINT __Machinist_BB__ Foot_section_only](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/1/9/198f3268705b5da00dbd2e48f87c2b8fa3b4392f.png) > > > > (excerpt from a file from Bill that I downloaded once a while ago)) > > This is from Onefinity: > > > [@Onefinity Foot Diagram](https://forum.onefinitycnc.com/t/onefinity-foot-diagram/13526/1): > > > > ![thumbnail_image001](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/2X/7/7aee34c1cdbce0ffdd9b09964fefeb729a5eceaf.png) > > > [@Differences Between X-50 Rails (upgrade) and X-35 Rails (standard)](https://forum.onefinitycnc.com/t/differences-between-x-50-rails-upgrade-and-x-35-rails-standard/6033/1): > > > > ![Machinist vs X-50 End View Stock Photo](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/a/6/a6d9520a4eb4011bcdd5285956e8c459ed87c389.jpeg) > > _Image: Left: Foreman model foot. Right: Journeyman, Woodworker and Machinist models feet._ > **Note that the footprint for a single foot is the same for all machines** , even if Foreman machine has higher feet. > > > [@Swelling issues, Table](https://forum.onefinitycnc.com/t/swelling-issues-table/17642/10): > > > > Someone offsite suggested that I could bolt it to the table rather than screwing, and then using large washers, or backing board, to eliminate the chance of the screws pulling out of the MDF when hung. If bolts are possible, I may be able to use the HMR with a Torsion Box and support the 1F from the inside of the box. Metal plates for instance. > > Sure. Good idea. That’s how I plan to do it. But I would not use [MDF](https://en.wikipedia.org/wiki/Medium-density_fibreboard) to build a table. It is too soft, too flexible, and of heavy weight at same time. [Plywood](https://en.wikipedia.org/wiki/Plywood) is much stiffier. Also MDF is much more prone to swelling as plywood. As for highly moisture resistant (HMR) MDF, I have no experience, never saw a use case. I use MDF only for speaker cabinets, where you want no acoustic resonance. Or for a wasteboard, but I think I will try the HDPE wasteboard as [discussed the other day](https://forum.onefinitycnc.com/t/new-waste-board/14757/15). HDPE is 100% recyclable, simply by melting it. MDF is (by far) not. > [@Removing X Axis or Y Axis stepper motors](https://forum.onefinitycnc.com/t/removing-x-axis-or-y-axis-stepper-motors/8718/8): > > > [@Removing X Axis or Y Axis stepper motors](https://forum.onefinitycnc.com/t/removing-x-axis-or-y-axis-stepper-motors/8718/6): > > > > How do I disconnect the wiring? X & Y rails > > [![Remove_screw_farthest_away_from_the_motor_on_bottom_of_front_foot_](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/4/7/47636e2fdc706cb4c920fbdee604f59977114bae.png) > Support: How to Access the inner tube motor wire – Youtube ](https://www.youtube.com/watch?v=YyB5QJ7neVQ) > > > [@Can someone measure their Elite Foreman Feet for me?](https://forum.onefinitycnc.com/t/can-someone-measure-their-elite-foreman-feet-for-me/25724/6): > > > > PS: It is also wise to to provide an opening on the underside of the table top or anti-torsion box to access the screw the farthest away from the stepper motor that loosens the front end cap of the lower tube with a 3 mm hex key to service the inner wire and the connector or the be able to replace the stepper motor. **If you don’t have such a service hole in your table, you’ll have to disassemble the entire machine to access the inner tube motor wire ☹** > > #### See also > > - [How to remove the motor from the end of the rail](https://www.youtube.com/watch?v=wXs3e-eecFk) > - [Support: How to determine if a wire or motor is damaged](https://forum.onefinitycnc.com/t/support-how-to-determine-if-a-wire-or-motor-is-damaged/18446) > - [Changing a motor on the Onefinity Elite Series](https://www.youtube.com/watch?v=8KdbeQPBwwc) > - [Onefinity CNC Original Series High Torque Motor Upgrade | Support Video](https://www.youtube.com/watch?v=qPhTSgx2Qp4) ---
**Author:** ![Okie1](https://avatars.discourse-cdn.com/v4/letter/o/b5e925/32.png) [@Okie1](https://forum.onefinitycnc.com/u/Okie1)\ **Post date:** [October 22, 2024, 8:32pm UTC](https://forum.onefinitycnc.com/t/onefinity-foot-bolt-size-table-anti-torsion-box/29031/4 "2024-10-22T20:32:45Z")
Thanks for the assistance.