# Pocket finish problem

**URL:** <https://forum.onefinitycnc.com/t/pocket-finish-problem/23775>\
**Category:** Uncategorized\
**Created:** [December 2, 2023, 8:21pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775 "2023-12-02T20:21:28Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![bkwoood](https://avatars.discourse-cdn.com/v4/letter/b/f04885/32.png) [@bkwoood](https://forum.onefinitycnc.com/u/bkwoood)\
**Post date:** [December 2, 2023, 8:21pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/1 "2023-12-02T20:21:28Z")

</div>

I made a tray/charcuterie board with round and rectangle pockets. It turned out nice except for the pocket side walls. They have ridges on them, The bit went back and forth then did a dia, cut. In other words on a 3in circle the cutter went back and forth then went around the 3in. Same thing for the rectangle pockets. Is there away to correct this ? I was expecting the bit to cut in a circular pattern not back and forth. Is that normal? thank you

---

<div class="post-metadata">

**Author:** ![PezWoodworks](https://avatars.discourse-cdn.com/v4/letter/p/ea5d25/32.png) [@PezWoodworks](https://forum.onefinitycnc.com/u/PezWoodworks)\
**Post date:** [December 2, 2023, 9:07pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/2 "2023-12-02T21:07:53Z")

</div>

If you are using Vectric, in the pocket tool path you choose between offset or raster, offset is circular and raster is linear.  
If you want real clean walls leave a little stock on the pocket toolpath and finish it with a profile path with the bit going full depth in one pass  
Pat

---

<div class="post-metadata">

**Author:** ![bkwoood](https://avatars.discourse-cdn.com/v4/letter/b/f04885/32.png) [@bkwoood](https://forum.onefinitycnc.com/u/bkwoood)\
**Post date:** [December 2, 2023, 9:12pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/3 "2023-12-02T21:12:22Z")

</div>

I’m using carve co maker. I’m still new to all this. Those are great tips. I’ll check and see what the settings are. Thank you

---

<div class="post-metadata">

**Author:** ![bkwoood](https://avatars.discourse-cdn.com/v4/letter/b/f04885/32.png) [@bkwoood](https://forum.onefinitycnc.com/u/bkwoood)\
**Post date:** [December 2, 2023, 9:27pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/4 "2023-12-02T21:27:24Z")

</div>

yes it was set to raster

---

<div class="post-metadata">

**Author:** ![pootaholic](https://avatars.discourse-cdn.com/v4/letter/p/8e7dd6/32.png) [@pootaholic](https://forum.onefinitycnc.com/u/pootaholic)\
**Post date:** [December 3, 2023, 11:00pm UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/5 "2023-12-03T23:00:22Z")

</div>

I’m not sure in Carveco but in Vectric’s software there is a setting as Pat pointed out that allows you to leave a small amount of stock on the walls of the pocket which can then be machined using a conventional cut. Something like 0.02 would be sufficient.

---

<div class="post-metadata">

**Author:** ![BillSpencer86](https://avatars.discourse-cdn.com/v4/letter/b/ecb155/32.png) [@BillSpencer86](https://forum.onefinitycnc.com/u/BillSpencer86)\
**Post date:** [December 4, 2023, 12:05am UTC](https://forum.onefinitycnc.com/t/pocket-finish-problem/23775/6 "2023-12-04T00:05:48Z")

</div>

Just went through this as well. What works for me is offset the vector by 1/16” and do a full depth profile pass. I’m just more comfortable visualizing the different vectors as opposed to messing with the offset/allowance settings in the tool path. If you run it all with the same bit/same file just make sure you save the tool paths in the right order…cheers
