# Poor suction and dust control

**URL:** <https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522>\
**Category:** Troubleshooting (X35/X50)\
**Created:** [September 1, 2021, 2:42pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522 "2021-09-01T14:42:49Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![TourniquetRules](https://avatars.discourse-cdn.com/v4/letter/t/3d9bf3/32.png) [@TourniquetRules](https://forum.onefinitycnc.com/u/TourniquetRules)\
**Post date:** [September 1, 2021, 2:42pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/1 "2021-09-01T14:42:49Z")

</div>

I am using the Fein Turbo, Dust Deputy, and Suckit Boot Pro (all 6 months old). Initially I thought it worked okay but now it seems that the dust and shavings go anywhere but the vacuum. When the job is finished and I take the vacuum off it easily sucks everything up. If it matters it is in the enclosure designed by Mitz P, recommended Makita router, and Gcode generated in Fusion 360 with the recommended post processor for OF. Most of the carvings I have done are using 2D or 3D adaptive clearing

Any ideas where to continue troubleshooting?

---

<div class="post-metadata">

**Author:** ![ConvenientWoodwork](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/convenientwoodwork/32/22558_2.png) [@ConvenientWoodwork](https://forum.onefinitycnc.com/u/ConvenientWoodwork)\
**Post date:** [September 1, 2021, 2:53pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/2 "2021-09-01T14:53:40Z")

</div>

Are you adjusting your boot so the whiskers touch the workpiece (at the start of the cut, and during if significant material is removed)?

---

<div class="post-metadata">

**Author:** ![TourniquetRules](https://avatars.discourse-cdn.com/v4/letter/t/3d9bf3/32.png) [@TourniquetRules](https://forum.onefinitycnc.com/u/TourniquetRules)\
**Post date:** [September 1, 2021, 3:44pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/3 "2021-09-01T15:44:55Z")

</div>

Yes, the brush drags along the wood.

---

<div class="post-metadata">

**Author:** ![CncDiver](https://avatars.discourse-cdn.com/v4/letter/c/977dab/32.png) [@CncDiver](https://forum.onefinitycnc.com/u/CncDiver)\
**Post date:** [September 1, 2021, 4:05pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/4 "2021-09-01T16:05:41Z")

</div>

Is the plastic plate (with the hole in the middle for the bit to pass through) still in tact? My cracked and had a piece break off recently and that seriously affected the suction.

---

<div class="post-metadata">

**Author:** ![TourniquetRules](https://avatars.discourse-cdn.com/v4/letter/t/3d9bf3/32.png) [@TourniquetRules](https://forum.onefinitycnc.com/u/TourniquetRules)\
**Post date:** [September 1, 2021, 4:28pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/5 "2021-09-01T16:28:28Z")

</div>

That could definitely be it. I moved the boot up once and forgot and the spindle broke it when it moved down.

 ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/a/4/a4b70155166c9c79e29a65ec753d9d8343ae3e2a.jpeg)  
I thought I replaced it but it still looks cracked.

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [September 1, 2021, 4:32pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/6 "2021-09-01T16:32:45Z")

</div>

you’re using the one intended for large bits, but you have a small bit installed, swap to the smaller plate.

---

<div class="post-metadata">

**Author:** ![TourniquetRules](https://avatars.discourse-cdn.com/v4/letter/t/3d9bf3/32.png) [@TourniquetRules](https://forum.onefinitycnc.com/u/TourniquetRules)\
**Post date:** [September 1, 2021, 5:06pm UTC](https://forum.onefinitycnc.com/t/poor-suction-and-dust-control/7522/8 "2021-09-01T17:06:25Z")

</div>

@OnefinityCNC  
Here is the current setup from 2 views with the 1/4 inch bit in place. There are several cracks and air gaps so that could be it.

 ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/c/7/c7fef805cc1c70450d9dffe19a9f30db26ddd6f9.jpeg)  
 ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/2X/4/4689926caf33f6e4e74636b6826f7d6372d4aebb.jpeg)
