# Probe problems/Mistakes **URL:** \ **Category:** Troubleshooting (X35/X50)\ **Created:** [January 8, 2023, 5:34pm UTC](https://forum.onefinitycnc.com/t/probe-problems-mistakes/17946 "2023-01-08T17:34:57Z")\ **Posts on this page:** 2\ **Page:** 1
**Author:** ![Leebones](https://avatars.discourse-cdn.com/v4/letter/l/e95f7d/32.png) [@Leebones](https://forum.onefinitycnc.com/u/Leebones)\ **Post date:** [January 8, 2023, 5:34pm UTC](https://forum.onefinitycnc.com/t/probe-problems-mistakes/17946/1 "2023-01-08T17:34:57Z")
So i accidentally hit the continue button and the machine started to probe z after a bit change. I hit stop but it is to close to the material now and i cant fit the probe block in. Is there a way to raise the z axis so i can fit it in there. The only way i have found is to hit stop and then start over, as you can imagine that is an extreme pain on a long carve. 2nd part: Is there a way to start from a certain spot in the code?? I have been just reloading toolpaths eliminating the portion that is already done. ---
**Author:** ![349iq2345](https://avatars.discourse-cdn.com/v4/letter/3/bb73d2/32.png) [@349iq2345](https://forum.onefinitycnc.com/u/349iq2345)\ **Post date:** [January 8, 2023, 5:53pm UTC](https://forum.onefinitycnc.com/t/probe-problems-mistakes/17946/2 "2023-01-08T17:53:58Z")
Hey Lee, > [@Leebones](#): > > So i accidentally hit the continue button and the machine started to probe z after a bit change. I hit stop but it is to close to the material now and i cant fit the probe block in. Is there a way to raise the z axis so i can fit it in there. The only way i have found is to hit stop and then start over, as you can imagine that is an extreme pain on a long carve. you see what’s in the ‘tool change’ field of the SETTINGS tab? This is what makes you’re stuck over your workpiece at the ‘tool change’ event with not enough room to actually change the bit. [Here’s how to make this ‘tool change’ routine usable](https://forum.onefinitycnc.com/t/tool-changes-and-z-height/7715/15#making-the-tool-change-routine-usable-1) ←. This applies to when you’re in program mode and are asked to change the bit. Note that when you hit “stop”, you leave the program mode and get back to manual mode. You can then freely move the milling motor around with the [gamepad](https://www.onefinitycnc.com/product-page/onefinity-wired-joystick), the [arrow buttons on display](https://buildbotics.com/manual-v1-0/#ControlPageJogTab), or by entering [G-code](https://en.wikipedia.org/wiki/G-code) commands into the command entry field of the [MDI Tab](https://buildbotics.com/manual-v1-0/#ControlPageMDITab) (in the [Tabbed Section](https://buildbotics.com/manual-v1-0/#tabbedsection)). However you cannot resume your program then. Instead of hitting “stop”, you can press “pause” by clicking on the “play” button. This makes you’re still in program mode and you can resume program at any time. But in program mode, > [@Don't estop on probe fail](https://forum.onefinitycnc.com/t/dont-estop-on-probe-fail/2171/18): > > the [gamepad](https://www.onefinitycnc.com/product-page/onefinity-wired-joystick) and the [arrow buttons on display](https://buildbotics.com/manual-v1-0/#ControlPageJogTab) are not active during g-code program execution, even during pause or tool-change event. This is is a [key element missing from the Onefinity and Buildbotics controllers](https://forum.onefinitycnc.com/t/heres-a-key-element-missing-from-the-bb-controller/10405): There is [no jogging possible in program mode](https://forum.onefinitycnc.com/t/controller-software-tool-change-location-0-0-g54-g55-g56/10052/12) ([no jogging in x y or z possible during tool change event](https://forum.onefinitycnc.com/t/like-many-new-forums-the-excitement-and/9209/32#no-jogging-in-x-y-or-z-possible-during-tool-change-event-m6-1)). > > This a [feature requested](https://forum.onefinitycnc.com/c/feature-requests/15): [Tool change jogging plus notifcation/ETA of toolchange](https://forum.onefinitycnc.com/t/tool-change-jogging-plus-notifcation-eta-of-toolchange/6091). > [@Leebones](#): > > 2nd part: Is there a way to start from a certain spot in the code?? Unfortunately, the Onefinity Controller and the [Buildbotics.com](http://Buildbotics.com) Controller do not support that. Welcome to the forum!