# QCW Fix Stand And Fixed Leg Kit **URL:** \ **Category:** Announcements\ **Created:** [November 23, 2022, 8:03pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665 "2022-11-23T20:03:20Z")\ **Posts on this page:** 20\ **Page:** 2
**Author:** ![Alan\_Richardson](https://avatars.discourse-cdn.com/v4/letter/a/b5e925/32.png) [@Alan\_Richardson](https://forum.onefinitycnc.com/u/Alan_Richardson)\ **Post date:** [July 30, 2026, 1:27pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/21 "2026-07-30T13:27:00Z")
Is your bench mounted on wheels? It could be the mechanism in the wheel housing moving with the side force generated by the gantry. ---
**Author:** ![creativesolutions](https://avatars.discourse-cdn.com/v4/letter/c/5fc32e/32.png) [@creativesolutions](https://forum.onefinitycnc.com/u/creativesolutions)\ **Post date:** [July 30, 2026, 2:07pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/22 "2026-07-30T14:07:19Z")
I have an Elite Foreman with QCW heavy duty support. My only issue is deflection with the Z axis. It sometimes leaves steps in the finish. It gets worse the closer you get to the center. ---
**Author:** ![Alan\_Richardson](https://avatars.discourse-cdn.com/v4/letter/a/b5e925/32.png) [@Alan\_Richardson](https://forum.onefinitycnc.com/u/Alan_Richardson)\ **Post date:** [July 30, 2026, 2:38pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/23 "2026-07-30T14:38:57Z")
Mine does the same thing. You need to tram it. The gantry is leaning. Unfortunately I haven’t found a new video on tramming the unit and i can’t find the adjusting screws in the frame. They’ve changed it. But there’s hope. Using raster, set it at 90 degrees surfacing along the Y axis. Also reduce your step over to 30%. This will force the bit to stay in one final level although it’s leaning. ---
**Author:** ![BigG](https://avatars.discourse-cdn.com/v4/letter/b/47e85d/32.png) [@BigG](https://forum.onefinitycnc.com/u/BigG)\ **Post date:** [July 30, 2026, 5:07pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/24 "2026-07-30T17:07:19Z")
The heavy duty is a good product. Very solid. ---
**Author:** ![hipgorilla](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/hipgorilla/32/35387_2.png) [@hipgorilla](https://forum.onefinitycnc.com/u/hipgorilla)\ **Post date:** [July 30, 2026, 6:09pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/25 "2026-07-30T18:09:16Z")
I’m thinking of printing some of these: [https://www.printables.com/model/1579955-onefinity-foot-riser#preview.8yQaC](https://www.printables.com/model/1579955-onefinity-foot-riser#preview.8yQaC) Then adding some of these: > **[FIZAR 4 Pack Heavy Duty Leveling Casters for Workbench 2200 LBS Capacity,...](https://www.amazon.com/FIZAR-LEVEING-CASTERS/dp/B0GW2GVGP7?tag=benmyers-20)** > > FIZAR 4 Pack Heavy Duty Leveling Casters for Workbench 2200 LBS Capacity, Upgraded Handle Design Retractable Caster Wheels Set,360 Degree Swivel Castors for Machine, Equipment, Shelves (Black): Amazon.com: Industrial & Scientific Haven’t gotten my GEN2 setup yet but coming soon. 😁 ---
**Author:** ![Joey](https://avatars.discourse-cdn.com/v4/letter/j/f14d63/32.png) [@Joey](https://forum.onefinitycnc.com/u/Joey)\ **Post date:** [July 30, 2026, 6:13pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/26 "2026-07-30T18:13:22Z")
I have the Foreman I built a strong table and put a granite top on it. Within.002 all around. ---
**Author:** ![mcircos](https://avatars.discourse-cdn.com/v4/letter/m/278dde/32.png) [@mcircos](https://forum.onefinitycnc.com/u/mcircos)\ **Post date:** [July 30, 2026, 7:24pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/27 "2026-07-30T19:24:25Z")
I added leveling casters to my frame without any big modifications. The current threaded feet use an M10 bolt, and you can get leveling casters that mount with a single M12 bolt. I picked up adapters on amazon that convert M12 to M10, this plus a small spacer block let me mount the leveling casters in a way where I could easily go back to feet if I wanted to. ![IMG_4102](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/4/5/45cc1362c27aa5655033cd45afafee37296b826e.jpeg) ![IMG_4103](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/1/8/18657691226e9cf8be4e61b9c681f45c6bd9fc71.jpeg) > **[Amazon.com: Trollastor Leveling Stem Casters, Casters Set of 4 Heavy Duty with...](https://www.amazon.com/Leveling-Casters-Adjustable-Upgraded-Ratchet/dp/B0DWNGQ3CF?tag=benmyers-20)** > > Amazon.com: Trollastor Leveling Stem Casters, Casters Set of 4 Heavy Duty with Upgraded Ratchet Handle Design, 360 Degree Swivel Castor Wheels, Adjustable Casters with Feet for Workbench, Total Capacity 2200 Lbs : Industrial & Scientific > **[Amazon.com: HiPicco 6Pcs Thread Adapter Sleeve Reducing Nut,M16 M to M8 F, 20mm...](https://www.amazon.com/HiPicco-Reducing-Stainless-Conversion-Fastener/dp/B0F8H8QRWM?tag=benmyers-20)** > > Buy HiPicco 6Pcs Thread Adapter Sleeve Reducing Nut,M16 M to M8 F, 20mm Length | M16 x 2 Male to M8 x 1.25 Female Thread, 303 Stainless Steel, Repair Insert Nut Screw Reducer Conversion Fastener: Nut Inserts - Amazon.com ✓ FREE DELIVERY possible on... ---
**Author:** ![sbillups](https://avatars.discourse-cdn.com/v4/letter/s/d2c977/32.png) [@sbillups](https://forum.onefinitycnc.com/u/sbillups)\ **Post date:** [July 31, 2026, 3:13am UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/28 "2026-07-31T03:13:34Z")
Hi Mike C, What table do you have? Where did you get the spacers? I have a Foreman Gen 1. If like to be able to roll it on two small ramps on either side of my welding table to straddle the table. ---
**Author:** ![mcircos](https://avatars.discourse-cdn.com/v4/letter/m/278dde/32.png) [@mcircos](https://forum.onefinitycnc.com/u/mcircos)\ **Post date:** [July 31, 2026, 11:20am UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/29 "2026-07-31T11:20:04Z")
I have a Journeyman Gen2 with the heavy duty leg kit. I 3D printed the spacers, but they arent anything special, just a cylinder to roughly match the hole that the threaded feet fit into. ---
**Author:** ![sbillups](https://avatars.discourse-cdn.com/v4/letter/s/d2c977/32.png) [@sbillups](https://forum.onefinitycnc.com/u/sbillups)\ **Post date:** [July 31, 2026, 11:55am UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/30 "2026-07-31T11:55:02Z")
That sounds great. Any chance you have pics of them attached? –Stefan ---
**Author:** ![mcircos](https://avatars.discourse-cdn.com/v4/letter/m/278dde/32.png) [@mcircos](https://forum.onefinitycnc.com/u/mcircos)\ **Post date:** [July 31, 2026, 2:28pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/31 "2026-07-31T14:28:10Z")
![IMG_4149](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/2/4/243c76d1746983d516a040748f8d0b0ec64dbfda.jpeg) ---
**Author:** ![Sinzard](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/sinzard/32/32876_2.png) [@Sinzard](https://forum.onefinitycnc.com/u/Sinzard)\ **Post date:** [July 31, 2026, 2:48pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/32 "2026-07-31T14:48:44Z")
i gotta say that is one Beautiful looking setup there. My gen 2 woodworker already shipped waiting on that leg/stand kit to ship as well. Very nice… ---
**Author:** ![Joey](https://avatars.discourse-cdn.com/v4/letter/j/f14d63/32.png) [@Joey](https://forum.onefinitycnc.com/u/Joey)\ **Post date:** [July 31, 2026, 3:12pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/33 "2026-07-31T15:12:25Z")
I have my Forman mounted to a granite plate. Being from the metal working industry I know you need rigidity and weight helps a lot. A small Haas weighs 7000 pounds. I haven’t run It yet (could use some help with that) thanks. ---
**Author:** ![Alan\_Richardson](https://avatars.discourse-cdn.com/v4/letter/a/b5e925/32.png) [@Alan\_Richardson](https://forum.onefinitycnc.com/u/Alan_Richardson)\ **Post date:** [July 31, 2026, 4:29pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/34 "2026-07-31T16:29:11Z")
Is there space for a vertical drop through for end milling? ---
**Author:** ![CaltechNerd](https://avatars.discourse-cdn.com/v4/letter/c/edb3f5/32.png) [@CaltechNerd](https://forum.onefinitycnc.com/u/CaltechNerd)\ **Post date:** [July 31, 2026, 5:12pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/35 "2026-07-31T17:12:19Z")
I love your setup. But what I’m really really pining for is enough space for the machine. I had to settle for a Machinist (16"x16") due to a full set of woodworking tools in a very limited space. DARN I envy you your space! ---
**Author:** ![Joey](https://avatars.discourse-cdn.com/v4/letter/j/f14d63/32.png) [@Joey](https://forum.onefinitycnc.com/u/Joey)\ **Post date:** [July 31, 2026, 5:35pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/36 "2026-07-31T17:35:55Z")
? What vertical drop through ---
**Author:** ![mrdropagear](https://avatars.discourse-cdn.com/v4/letter/m/a3d4f5/32.png) [@mrdropagear](https://forum.onefinitycnc.com/u/mrdropagear)\ **Post date:** [July 31, 2026, 7:18pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/37 "2026-07-31T19:18:50Z")
I ended up with a 50x100 inch table journeyman on top table came with the machine. She barely fits in one corner of my 12x16 shed. It is tight so I wouldnt mind swapping to a smaller table to reclaim some space in the shed but extra table space is always nice when you dont have a ton of flat space. ---
**Author:** ![hipgorilla](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/hipgorilla/32/35387_2.png) [@hipgorilla](https://forum.onefinitycnc.com/u/hipgorilla)\ **Post date:** [August 3, 2026, 3:54pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/38 "2026-08-03T15:54:04Z")
Could be mistaken but I believe he is referring to an area at the front of the CNC where the spindle can still reach yet it allows for the piece to be vertically held rather than flat on the bed horizontally. One can do interesting milling on the ends of pieces with that. ---
**Author:** ![perryjj](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/perryjj/32/35891_2.png) [@perryjj](https://forum.onefinitycnc.com/u/perryjj)\ **Post date:** [August 3, 2026, 4:12pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/39 "2026-08-03T16:12:37Z")
The gentleman, Dakotah Konicek, from SpruceKnotLab on Etsy, sells plans for a vertical jig and a compound angle adjustment. I ordered it in anticipation of my order from Onefinity. jp ---
**Author:** ![Mnutter99](https://avatars.discourse-cdn.com/v4/letter/m/85f322/32.png) [@Mnutter99](https://forum.onefinitycnc.com/u/Mnutter99)\ **Post date:** [August 3, 2026, 4:34pm UTC](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665/40 "2026-08-03T16:34:18Z")
I am sorry to hear of your loss. May God give you peace and blessings through this hard Time. I will drop the file off today. Mark [Previous page](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665.md?page=1) [Next page](https://forum.onefinitycnc.com/t/qcw-fix-stand-and-fixed-leg-kit/16665.md?page=3)