# Woodworker and J-Tech laser

**URL:** <https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344>\
**Category:** J Tech Laser\
**Created:** [November 7, 2022, 5:21pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344 "2022-11-07T17:21:09Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Lance249](https://avatars.discourse-cdn.com/v4/letter/l/9dc877/32.png) [@Lance249](https://forum.onefinitycnc.com/u/Lance249)\
**Post date:** [November 7, 2022, 5:21pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344/1 "2022-11-07T17:21:09Z")

</div>

As I start with the J-Tech on my Woodworker, does any one have what the MAX travel speed while lasering is? I don’t want to overextend the woodworker. I have been trying to look through other posts and may have missed it.

---

<div class="post-metadata">

**Author:** ![Bern](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/bern/32/7185_2.png) [@Bern](https://forum.onefinitycnc.com/u/Bern)\
**Post date:** [December 18, 2022, 12:57pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344/2 "2022-12-18T12:57:41Z")

</div>

I wouldn’t mind knowing this as well… so giving this a bump

---

<div class="post-metadata">

**Author:** ![Woodworking\_Pilot](https://avatars.discourse-cdn.com/v4/letter/w/e9bcb4/32.png) [@Woodworking\_Pilot](https://forum.onefinitycnc.com/u/Woodworking_Pilot)\
**Post date:** [January 5, 2023, 3:21pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344/3 "2023-01-05T15:21:52Z")

</div>

@Lance249 according to the user manual the X and Y axis “rapid rate” is 500 in/min. It doesn’t necessarily state that is a limit, but that is the only speed listed. Maybe @OnefinityCNC could verify? I am curious too know as I just got the 24w and am trying to figure our the best way to maximize the increase in power. If I can go up to 500 in/min while engraving that could be a huge time saver.

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [January 5, 2023, 3:35pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344/4 "2023-01-05T15:35:52Z")

</div>

You could set it to 1 million, but it will never go faster than the max travel of the machine, 398IPM.

---

<div class="post-metadata">

**Author:** ![Woodworking\_Pilot](https://avatars.discourse-cdn.com/v4/letter/w/e9bcb4/32.png) [@Woodworking\_Pilot](https://forum.onefinitycnc.com/u/Woodworking_Pilot)\
**Post date:** [January 5, 2023, 11:27pm UTC](https://forum.onefinitycnc.com/t/woodworker-and-j-tech-laser/16344/5 "2023-01-05T23:27:56Z")

</div>

@OnefinityCNC Thank You!!

I guess I’m going to see what 120-240 looks like on the 24w laser