# Working Wireless MPG Pendant

**URL:** <https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484>\
**Category:** Elite Series (Masso & Redline) (Gen 1)\
**Created:** [November 20, 2023, 3:09am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484 "2023-11-20T03:09:31Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 20, 2023, 3:09am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/1 "2023-11-20T03:09:31Z")

</div>

[Here is a video of my Elite Foreman with a wireless pendant.](https://youtu.be/lgphwPbB3uM)

[Here is a link to the pendant](https://www.wixhc.cn/product/enhanced-wireless-handwheel-with-e-stop-ztwgp-3). You need the 24v receiver, I contacted them directly for the purchase to make sure I got the correct receiver.

[Here is a link to the wiring diagram](https://github.com/eric-buzz/Onefinity/blob/main/wiXhc_to_MassoG3_wiring_diagram.png)

This this is pretty sweet and no stupid wire to get in my way.

---

<div class="post-metadata">

**Author:** ![poppyscott](https://avatars.discourse-cdn.com/v4/letter/p/a587f6/32.png) [@poppyscott](https://forum.onefinitycnc.com/u/poppyscott)\
**Post date:** [November 20, 2023, 3:58am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/2 "2023-11-20T03:58:29Z")

</div>

Looks pretty good. It is a bit pricey, though. Guess I’ll have to wear my current pendant out before I upgrade.

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 20, 2023, 4:23pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/3 "2023-11-20T16:23:11Z")

</div>

They make other models at different prices with different features and quality, I just want people to know that there are better option than just the wired version.

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [November 20, 2023, 4:29pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/4 "2023-11-20T16:29:04Z")

</div>

it must be a 24v volt version, most are 5v, so be aware.

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 20, 2023, 5:30pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/5 "2023-11-20T17:30:53Z")

</div>

it clearly states that in the original post.

> Here is a link to the pendant You need the 24v receiver, I contacted them directly for the purchase to make sure I got the correct receiver.

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [November 20, 2023, 5:33pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/6 "2023-11-20T17:33:00Z")

</div>

it’s worth mentioning twice, as 1 out of 2 buyers get the 5v 🙂

---

<div class="post-metadata">

**Author:** ![WaywardWoodworker](https://avatars.discourse-cdn.com/v4/letter/w/e79b87/32.png) [@WaywardWoodworker](https://forum.onefinitycnc.com/u/WaywardWoodworker)\
**Post date:** [November 20, 2023, 6:03pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/7 "2023-11-20T18:03:36Z")

</div>

The smoke is an included feature to let you know you purchased the wrong one.

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 20, 2023, 6:09pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/8 "2023-11-20T18:09:33Z")

</div>

I should mention that the newest version of the receiver that comes with it is 5v-24v compatible.

There was is a jumper you move to select the pulse voltage. You can see it in this picture.

 ![PXL_20231118_054003759.MP](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/c/a/ca0992de3385fd85ddd3b8e5814f0935879a31c0.jpeg)

---

<div class="post-metadata">

**Author:** ![BManCan](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/bmancan/32/31071_2.png) [@BManCan](https://forum.onefinitycnc.com/u/BManCan)\
**Post date:** [November 20, 2023, 6:14pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/9 "2023-11-20T18:14:17Z")

</div>

@buzzfab What type of batteries does the wireless MPG use? Thanks for sharing all the details for your setup.  
Nicely done.

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 21, 2023, 4:53am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/11 "2023-11-21T04:53:10Z")

</div>

@BManCan 2AA batteries

---

<div class="post-metadata">

**Author:** ![BManCan](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/bmancan/32/31071_2.png) [@BManCan](https://forum.onefinitycnc.com/u/BManCan)\
**Post date:** [November 22, 2023, 3:35pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/12 "2023-11-22T15:35:52Z")

</div>

@buzzfab what is the reason for wiring the input buttons using a pull up resistor? When you configure the input on the Masso does it end up being inverted (low when button pressed). Thx.

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [November 26, 2023, 3:41am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/13 "2023-11-26T03:41:39Z")

</div>

You need to wire it to ve+ for pull-up or ve- for pull down.  
If it isn’t it will be a floating input and could flicker back and forth between HIGH and LOW

here is s short explaination video [https://www.youtube.com/watch?v=wxjerCHCEMg](https://www.youtube.com/watch?v=wxjerCHCEMg)

more info from masso here  
[https://docs.masso.com.au/quick-start-guides/safe-work-practices](https://docs.masso.com.au/quick-start-guides/safe-work-practices)

---

<div class="post-metadata">

**Author:** ![mhackney](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/mhackney/32/9105_2.png) [@mhackney](https://forum.onefinitycnc.com/u/mhackney)\
**Post date:** [April 17, 2024, 6:28pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/14 "2024-04-17T18:28:01Z")

</div>

I am following on this and contacted the company and got the same MPG and gathered all of the other things I need. I traced the leads on the DB15 so I know which color wire goes with each pin. Long story short - it doesn’t work. Here’s what happens, hopefully someone has some ideas as I am out of them:

I’ve verified all of the connections. When I turn on the MASSO, the LED on the MPG receiver lights up. When I click one of the 2 buttons on the side of the handpiece, I hear a click from the receiver. In Screen 1 on the MASSO, all of the MPG inputs show as LOW(and No in the invert column). When I depress the side button and turn the MPG wheel, I see the Dual Signal - A and Dual Signal - B indicators flicker from LOW to HIGH (green and red) but nothing happens on the machine (and I tested this on Input screen. The MASSO documentation (in the troubleshooting section) describes this flickering as normal: [MPG Pendant](https://docs.masso.com.au/wiring-and-setup/setup-and-calibration/mpg-pendant)

I do not see any of the selected inputs on the handpiece go high on the F1 screen - the axis selects do not go high when I turn the knobs on the handpiece nor does the selected resolution show high. All of the inputs show LOW.

When I turn one of the input knobs, I do see the LED on the receiver flicker so that tells me the wireless connection between the handpiece and receiver is working. Even if I got one or several of the connections on the DB-15 wrong, the actual input should show high but I don’t see anything go high. There should always be one resolution select and one resolution select high.

The one difference in my connections is I did not connect the earth wire. I contacted the company and asked about this and a tech replied saying that it is not necessary.

Any ideas or suggestions greatly appreciated!

---

<div class="post-metadata">

**Author:** ![mhackney](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/mhackney/32/9105_2.png) [@mhackney](https://forum.onefinitycnc.com/u/mhackney)\
**Post date:** [April 17, 2024, 6:30pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/15 "2024-04-17T18:30:35Z")

</div>

I should also add that after moving the black wire from Estop 2 to Estop 1 on the controller as described, I can not clear the estop. Most likely this is related to the input issue I am trying to resolve in the last post. So, temporarily, I have both the black and green wires connected to the default factory at Estop 2 terminal.

---

<div class="post-metadata">

**Author:** ![mhackney](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/mhackney/32/9105_2.png) [@mhackney](https://forum.onefinitycnc.com/u/mhackney)\
**Post date:** [April 17, 2024, 7:11pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/16 "2024-04-17T19:11:08Z")

</div>

Found the problems!

For the inputs not working - turns out that the COM1 that provides V+ (terminal 1 on the receiver) to all of the selection inputs was not attached to the PWR terminal well (the insulation was, well, insulating the connection). That fixed that problem.

Then for the E-stop, close scrutiny of my wiring chart showed me that I connected the E-stop wire incorrectly. I had them connected to terminal 15 (black wire, correct) and 16 (red wire, incorrect!) it should be connected to terminal 18. Both E-stop buttons work properly now.

---

<div class="post-metadata">

**Author:** ![kpmnd85](https://avatars.discourse-cdn.com/v4/letter/k/76d3ee/32.png) [@kpmnd85](https://forum.onefinitycnc.com/u/kpmnd85)\
**Post date:** [April 24, 2024, 3:24am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/18 "2024-04-24T03:24:38Z")

</div>

I am trying to order the wireless pendent. I’ve specified the voltage for power is 24 volts. The technician has asked what the pulse voltage is. I said 24 volts as well. Tech came back and said they have supplied several of these for Onefinity systems and they configure the pulse voltage as 5 volts. The wiring diagram references 5v as I have circled.

 ![image](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/b/7/b717444199f267944d17af0f5af41f0a1a590591.jpeg)

Can someone confirm the PULSE voltage is 24 Volts? Thanks.

---

<div class="post-metadata">

**Author:** ![BManCan](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/bmancan/32/31071_2.png) [@BManCan](https://forum.onefinitycnc.com/u/BManCan)\
**Post date:** [April 24, 2024, 11:33am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/19 "2024-04-24T11:33:21Z")

</div>

As long as they provide the newer version of the wireless receiver as shown in previous post, it is configurable for 5V or 24V pulse voltage.  
[Working Wireless MPG Pendant - #8 by buzzfab](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/8)

---

<div class="post-metadata">

**Author:** ![kpmnd85](https://avatars.discourse-cdn.com/v4/letter/k/76d3ee/32.png) [@kpmnd85](https://forum.onefinitycnc.com/u/kpmnd85)\
**Post date:** [April 24, 2024, 11:45am UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/20 "2024-04-24T11:45:47Z")

</div>

Thanks. It sounds like I will want to set the jumper to support 24v pulse voltage.

---

<div class="post-metadata">

**Author:** ![kpmnd85](https://avatars.discourse-cdn.com/v4/letter/k/76d3ee/32.png) [@kpmnd85](https://forum.onefinitycnc.com/u/kpmnd85)\
**Post date:** [May 21, 2024, 5:47pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/21 "2024-05-21T17:47:13Z")

</div>

I’m getting an unexpected homing sequence when I initially do an e-stop reset. I have a pull-up resistor wired to input 18 which I have set to “home machine” on the F1 screen and where I have a wire which goes to the input of the first button which I am using for “home”.

Seems like putting a pull-up on an input which is designated to home the machine is an issue.

Does anyone else experience this behavior?

---

<div class="post-metadata">

**Author:** ![buzzfab](https://avatars.discourse-cdn.com/v4/letter/b/d2c977/32.png) [@buzzfab](https://forum.onefinitycnc.com/u/buzzfab)\
**Post date:** [June 9, 2024, 2:42pm UTC](https://forum.onefinitycnc.com/t/working-wireless-mpg-pendant/23484/22 "2024-06-09T14:42:01Z")

</div>

It works fine for me.
