# X-50 Video - Install, Tramming, and Initial Thoughts

**URL:** <https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274>\
**Category:** Accessories\
**Created:** [June 21, 2021, 12:40am UTC](https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274 "2021-06-21T00:40:29Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [June 21, 2021, 12:40am UTC](https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274/1 "2021-06-21T00:40:29Z")

</div>

Hello everyone - comments of @OnefinityCNC I received and early version of the X-50 that I finally installed and completed a video for. Hopefully you find it informative! Feedback and questions are welcome.

[![](https://us1.discourse-cdn.com/flex022/uploads/onefinitycnc/original/3X/c/9/c992fa58e17f43cb985ea599b8af1457e6f0072a.jpeg "Onefinity CNC X-50 Upgrade - Features, Install and Thoughts") ](https://www.youtube.com/watch?v=geE3Bos4XN8)

-Tom

---

<div class="post-metadata">

**Author:** ![Cdavis](https://avatars.discourse-cdn.com/v4/letter/c/e9bcb4/32.png) [@Cdavis](https://forum.onefinitycnc.com/u/Cdavis)\
**Post date:** [June 21, 2021, 3:14am UTC](https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274/2 "2021-06-21T03:14:36Z")

</div>

Great review of the X-50 upgrade. I am curious about the tramming bolts you mentioned that are on the X-50, and I believe you said are also on the original X axis. Can you provide a closeup shot and explain how these are used to adjust front-to-back tramming? My machine is fine side to side but is off slightly front to back, and I’ve been trying to decide the best way to adjust.  
Thanks!

---

<div class="post-metadata">

**Author:** ![MustCreateThings](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/mustcreatethings/32/3771_2.png) [@MustCreateThings](https://forum.onefinitycnc.com/u/MustCreateThings)\
**Post date:** [June 21, 2021, 11:56am UTC](https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274/3 "2021-06-21T11:56:12Z")

</div>

Thank yo for the video and congrats on becoming a Beta tester!

\_Mike

---

<div class="post-metadata">

**Author:** ![cyberreefguru](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/cyberreefguru/32/27385_2.png) [@cyberreefguru](https://forum.onefinitycnc.com/u/cyberreefguru)\
**Post date:** [June 21, 2021, 6:02pm UTC](https://forum.onefinitycnc.com/t/x-50-video-install-tramming-and-initial-thoughts/6274/4 "2021-06-21T18:02:26Z")

</div>

Thanks Mike!

Carroll - I need to look at the old Y carriage, but you should just tighten the lower to push it forward, and tighten the upper to push it back - you might have to loosen the back side bolts while you tighten the front side.

-Tom