# X axis not registering full cutting width

**URL:** <https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135>\
**Category:** Original/PRO Series (Buildbotics) (Gen 1)\
**Created:** [August 19, 2025, 2:23pm UTC](https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135 "2025-08-19T14:23:21Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![AJKremer](https://avatars.discourse-cdn.com/v4/letter/a/e9bcb4/32.png) [@AJKremer](https://forum.onefinitycnc.com/u/AJKremer)\
**Post date:** [August 19, 2025, 2:23pm UTC](https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135/1 "2025-08-19T14:23:21Z")

</div>

Good morning!

I have an OG Woodworker x-35, I am in the process of setting up the match fit waste board, however, when I go do measure the max X and Y, the X axis only registers to 20 in (??)

I am on the current version (1.6.4) and have reset and restarted multiple times with the same outcome.

What am I missing?

TIA!

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [August 19, 2025, 2:47pm UTC](https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135/2 "2025-08-19T14:47:36Z")

</div>

Reset the configuration to your specific machine:  
X35 woodworker  
Z16 z slider

> [@How To Reset The Configuration To Defaults (BB Controller) (FAQ)](https://forum.onefinitycnc.com/t/how-to-reset-the-configuration-to-defaults-bb-controller-faq/2547):
>
> Occasionally, there may be a time when you need to reset the machine back to factory defaults. Here’s how to perform a configuration reset. (machine not working correctly, machine cutting shrunk or stretched, ipp rail upgrade sizes) Please note, resetting the configuration will change any custom values you have entered (i.e. probe size, stall homing settings). Please make note of these BEFORE resetting so you can input them back in once reset. Always ensure you’re on the latest firmware (as …

---

<div class="post-metadata">

**Author:** ![AJKremer](https://avatars.discourse-cdn.com/v4/letter/a/e9bcb4/32.png) [@AJKremer](https://forum.onefinitycnc.com/u/AJKremer)\
**Post date:** [August 19, 2025, 3:04pm UTC](https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135/3 "2025-08-19T15:04:20Z")

</div>

Sorry, this still didn’t fix the issue.

Once reset and restarted - jogged to max X and it still registers 20.29 in

---

<div class="post-metadata">

**Author:** ![OnefinityCNC](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.onefinitycnc.com/onefinitycnc/32/7_2.png) [@OnefinityCNC](https://forum.onefinitycnc.com/u/OnefinityCNC)\
**Post date:** [August 19, 2025, 3:23pm UTC](https://forum.onefinitycnc.com/t/x-axis-not-registering-full-cutting-width/35135/4 "2025-08-19T15:23:35Z")

</div>

Did you do an update to a IPP rail? If so, then you have an x50 rail, so you’d choose x50/pro woodworker and save and restart.

Email [support@onefinitycnc.com](mailto:support@onefinitycnc.com) if that doesn’t fix it.