I’ve just setup my new Redline spindle. All seems to be good running the break-in currently. I am trying to figure out why the VFD controller is displaying 2.5 when everything is idle. I have the 220 model and like I said all so far seems to be working just fine. The speed is displayed when the spin…

I spoke with Onefinity this morning and they said this was normal. I asked if a parameter could be adjusted to display 0 at idle. They said I needed to reach out to Redline with that question. I’ll do that this next week and see what they say. Another bit of info, it displays 2 or 2.5 only when the …

Just an update on this from Redline. Seems the 2 or 2.5 is the current. This is the reply from Redline: The 2.0 or 2.5 displayed shows the voltage, current, or frequency that is currently running through the system. It will not display RPM’s until it is told to turn the spindle on either through g…

Hey @kenmachdata , thanks for this. I have one on the way and I would have been stuck on this. I just had my soon to ship order changed from the 80mm 100v to the 220v. What 220 plug is it using? I need to add an outlet.

NEMA 6-30P, thank you very much good sir! Turns out it was a lot easier to get 220 in my garage than I thought when I ordered. And I already ran two new dedicated 100v 20A circuits to 2-20R outlets to where the machine will live. With your help, I can now have one of those changed out to the prope…

OH, orrrrrr. Could be a 6-15. same layout, different size pins. grrr. plenty of time. hurrrdurrrr, RTFM. right there. thought 30 seemed excessive [image]

I ran new dedicated circuits to the table as well. One 110 and a 220. The 220 is 6-20R and the 110 is standard 15 amp 110 outlet. Both are now part of my table where as before both lived at the wall. Very convenient to have as part of the table. I’m always plugging in something and not having cords …

Remember too that if you already have 220 in the garage but not the correct outlet for your type of machine, they sell all kinds of adapters for just about any 220V outlet/plug combination. If you don’t want to have an electrician change your outlet to the one you need, they are anywhere from 10 to …

Fortunately enough, my neighbor is an industrial electrician, and I have a friend who runs his own resi company as well. So I get advice, if not actual work, from sparkies for free. So I got that going for me, which is nice. The spot where the 220 will go is currently run as a 110 20A, I have enou…

New Redline Spindle Install

Onefinity Spindle Kit by Redline CNC 80mm 2.2kw Air Cooled

Ken5 April 23, 2025, 2:02pm 5

This one

Regards au 240 volt machine and spindle

What type of Plug for Redline 220v spindle?

Topic		Replies	Views
Spindle running at half speed Troubleshooting (X35/X50)	31	7295	January 21, 2025
Configuring Redline Spindle/VFD with the Pro CNC Onefinity Spindle Kit by Redline CNC	1	239	May 28, 2025
New trouble, very dangerous (Solved, VFD requires reprogramming) Onefinity Spindle Kit by Redline CNC	72	1027	May 1, 2026
"A Man's GOT to Know His Limitations" Original/PRO Series (Buildbotics) (Gen 1)	37	3132	November 17, 2021
RPM Range of VFDs Spindle/VFD (Aftermarket/Unsupported)	26	4795	September 27, 2023

New Redline Spindle Install

Related topics