I have made an error when updating the Masso link software and deleted the machine setting file. I attach my back-up file of the latest settings, that I have put into the controller. Unfortunately, I am now getting motor errors and hard limit errors, which I never experienced previously. Is it possible for someone to look at the file and either correct my errors or provide me with a file that will work for the basic setting and I would then correct for my file and reinstall the ATC and Probes etc. Many thanks in advance for your support. MASSO G3 Touch Serial No: G3-30991 Hardware: v3.09 Core: v2.07 Software: 5-Axis, v5.13 Settings file format: v2.40 ==========General Settings========== Machine units: Inch Machine bed orientation: Standard Load ‘autoload.nc’ on power up: Disable Soft Limits: Disable Hard Limits: Enable cycle start on door close: Limit maximum feedrate: ==========Homing Settings========== Seq 1: X: 0 Y: 0 Z: 1 A: 0 B: 0 Seq 2: X: 1 Y: 0 Z: 0 A: 0 B: 0 Seq 3: X: 0 Y: 1 Z: 0 A: 0 B: 0 Seq 4: X: 0 Y: 0 Z: 0 A: 0 B: 0 Seq 5: X: 0 Y: 0 Z: 0 A: 0 B: 0 X-Axis Direction Invert: Ticked Y-Axis Direction Invert: Ticked Z-Axis Direction Invert: A-Axis Direction Invert: B-Axis Direction Invert: Ticked Homing Feedrate: 40 X-Axis Sensor Pull-Off: 0.040000 Y-Axis Sensor Pull-Off: 0.040000 Z-Axis Sensor Pull-Off: 0.040000 A-Axis Sensor Pull-Off: 0.040000 B-Axis Sensor Pull-Off: 0.040000 X-Axis Position After Homing: 0.000000 Y-Axis Position After Homing: 0.000000 Z-Axis Position After Homing: 0.000000 A-Axis Position After Homing: 0.000000 B-Axis Position After Homing: 0.000000 Request Home on startup: Ticked Request Home after E-Stop press: Ticked ==========Spindle Settings========== Encoder (Pulses per revolution): 2000 Spindle Control Method: VFD (0~10v) Spindle RPM at 10 volts: 24000 Spin UP delay (milliseconds): 6000 Spin DOWN delay (milliseconds): 6000 ==========Lubrication Settings========== Lubricate after: 0(hr) & 10(min) Lubricate for: 0(min) & 3(sec) ==========Tool Changer========== Tool changer in use: 1: Manual Tool Change Tool setter air blast time (ms): 0 =============X-Axis============= Motor: Distance per revolution: 0.629920 Drive: Pulses per revolution: 2000.000000 Maximum Feedrate: 600.000671 Acceleration: 19.685221 Travel Minimum: 0.000000 Travel Maximum: 48.031437 Backlash: 0.000000 Direction Invert: =============Y-Axis============= Motor: Distance per revolution: 0.629920 Drive: Pulses per revolution: 400.000000 Maximum Feedrate: 600.000671 Acceleration: 19.685362 Travel Minimum: 0.000000 Travel Maximum: 48.374744 Backlash: 0.000000 Direction Invert: Ticked =============Z-Axis============= Motor: Distance per revolution: 0.393700 Drive: Pulses per revolution: 2000.000000 Maximum Feedrate: 300.000366 Acceleration: 19.685122 Travel Minimum: -6.299203 Travel Maximum: 0.000000 Backlash: 0.000000 Direction Invert: =============A-Axis============= Motor: Distance per revolution: 360.000000 Drive: Pulses per revolution: 14000.000000 Maximum Feedrate: 4320.000000 Acceleration: 2000.000000 Travel Minimum: -720.000000 Travel Maximum: 720.000000 Backlash: 0.000000 Direction Invert: Ticked Angular Axis: Ticked =============B-Axis============= Slaved to Y axis Direction Invert: ==========Auto Tool Zero Settings========== Only auto tool zero when manually requested: Tool setter X position: 0.000000 Tool setter X enable: Tool setter Y position: 0.000000 Tool setter Y enable: Z safe distance to tool setter: 0.000000 Tool zero feedrate: 20.000011 Tool number to skip: 5 ==========Multi Head Settings========== Dry Run: Disabled Multi Spindle-1 (T101): Disabled Multi Spindle-2 (T102): Disabled Multi Spindle-3 (T103): Disabled Multi Spindle-4 (T104): Disabled Laser Engraving/Cutting (T111): Disabled Plasma Torch (T112): Disabled Oxy Torch (T113): Disabled WaterJet (T114): Disabled Scribe Tool (T115): Disabled Pen 1 (T116): Disabled Pen 2 (T117): Disabled Camera (T118): Disabled ==========INPUTS========== EStop: EStop, Invert: No Encoder: Signal - A, Invert: No Encoder: Signal - B, Invert: No Encoder: Index, Invert: No MPG: Dial Signal - A, Invert: No MPG: Dial Signal - B, Invert: No MPG: Select X, Invert: No MPG: Select Y, Invert: No MPG: Select Z, Invert: No MPG: Select A, Invert: No MPG: Select B, Invert: No MPG: Resolution 1, Invert: No MPG: Resolution 2, Invert: No MPG: Resolution 3, Invert: No Analog: Input 1, Invert: Analog: Input 2, Invert: Input 11: Tool Setter, Invert: No Input 12: Touch Probe, Invert: No Input 13: X - Home Sensor, Invert: No Input 14: Y - Home Sensor, Invert: No Input 15: B - Home Sensor, Invert: No Input 16: Z - Home Sensor, Invert: No Input 19: X-Axis Motor Alarm, Invert: No Input 20: Y-Axis Motor Alarm, Invert: No Input 21: Z-Axis Motor Alarm, Invert: No Input 22: B-Axis Motor Alarm, Invert: No ==========OUTPUTS========== Spindle: CW, Invert: No Spindle: CCW, Invert: No Output 11: Laser-Engraving (PWM), Invert: No Output 12: Coolant Flood, Invert: No ==========TOOLS DATA========== Tool-1, Slot: 1, 3.125 Jenny, Z Offset: -5.137208, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-2, Slot: 2, 3.125 Vbit, Z Offset: -3.242915, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-3, Slot: 3, 6.35 Upcut, Z Offset: -2.715946, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-4, Slot: 4, 6.35 Dcut, Z Offset: -5.479530, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-5, Slot: 5, manual, Z Offset: -3.473624, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-6, Slot: , , Z Offset: -5.353350, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-7, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-8, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-9, Slot: , , Z Offset: -4.116341, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-10, Slot: , , Z Offset: -4.653349, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-11, Slot: , 90 deg. V, Z Offset: 0.000000, Tool Dia: 0.375000, Tool Dia wear 0.000000 Tool-12, Slot: , , Z Offset: -4.950790, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-13, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-14, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-15, Slot: , , Z Offset: -4.489570, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-16, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-17, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-18, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-19, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-20, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-21, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-22, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-23, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-24, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-25, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-26, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-27, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-28, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-29, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-30, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-31, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-32, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-33, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-34, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-35, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-36, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-37, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-38, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-39, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-40, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-41, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-42, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-43, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-44, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-45, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-46, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-47, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-48, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-49, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-50, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-51, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-52, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-53, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-54, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-55, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-56, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-57, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-58, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-59, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-60, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-61, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-62, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-63, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-64, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-65, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-66, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-67, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-68, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-69, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-70, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-71, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-72, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-73, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-74, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-75, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-76, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-77, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-78, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-79, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-80, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-81, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-82, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-83, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-84, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-85, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-86, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-87, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-88, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-89, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-90, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-91, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-92, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-93, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-94, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-95, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-96, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-97, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-98, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-99, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-100, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-101, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-102, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-103, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Tool-104, Slot: , , Z Offset: 0.000000, Tool Dia: 0.000000, Tool Dia wear 0.000000 Workoffset - G54: X: 24.015404 Y: 24.185795 Z: 0.324219 A: 0.000000 Workoffset - G55: Main Fence X: 1.623517 Y: 3.411547 Z: -1.615946 A: 0.000000 Workoffset - G56: X: 0.000000 Y: 0.000000 Z: 0.000000 A: 0.000000 Workoffset - G57: X: 0.000000 Y: 0.000000 Z: 0.000000 A: 0.000000 Workoffset - G58: X: 0.000000 Y: 0.000000 Z: 0.000000 A: 0.000000 Workoffset - G59: X: 0.000000 Y: 0.000000 Z: 0.000000 A: 0.000000 Parking: Main X: 23.622061 Y: 11.811030 Z: 0.000000 A: 0.000000

[image] Elite Series Masso Default Machine Settings exclamation_question_markMasso Default Configuration FAQ Elite Series Masso Machine Settings: (updated: 11/3/25) There are three different parts that must be done: Upgrade the FIRMWARE to the latest Ensure all 4 of your motor dip switches are correct and updated Reload the factory default CONFIGURATION files. Part 1, 2, and 3 must be done in order. :one:Part 1: Firmware Before performing the two steps below, ensure the Masso firmware is 5.13 or later (Click Here to learn how to update your firmware, which is different than the below step #3 confi…

Masso settings lost Gen 1 Foreman

Elite Series (Masso & Redline) (Gen 1) Tool Setter

OnefinityCNC (Onefinity CNC Official ✅) September 13, 2026, 4:24pm 2

Topic		Replies	Views
Elite Series Masso Default Machine Settings Masso Default Configuration FAQ	0	13627	December 16, 2022
Tool Setter HOW TO! Elite Series (Masso & Redline) (Gen 1)	50	5243	September 17, 2024
Help! Axis distance problems (solved) Elite Series (Masso & Redline) (Gen 1)	7	206	April 1, 2025
Easy-Z Tool Setter Problems (what is the proper steps to use it) Accessories	45	2638	October 14, 2025
Order of Operations / what went wrong? (masso and tool setter) Elite Series (Masso & Redline) (Gen 1)	11	244	January 29, 2026

Masso settings lost Gen 1 Foreman

Related topics