Looking to learn from others as I design my table. I ordered the Foreman so the footprint of the machine is 64"x62.6". Requirements: Must contain the entire dimensions of the machine within the table footprint. Must be on a mobile base. Must have a removable section for vertical carve capabiliti…

Yes, the 90 degree corner brackets in addition to their corner brackets basically make it impossible to not get it square. I double checked everything with a square and tape measure and it was perfect. There is a cross brace going both directions (like a cross) under each layer of melamine. Clear…

It’s likely overkill, but I decided to add an adjustable center leg to my table frame. I was seeing some excessive deflection under certain point load conditions in the simulation. Adjustable section is 3/4"x10" all-thread for levelling with or without the casters. [TableCenterSupport]

Hi Keith, Nice table. I plan to do a similar aluminum extrusion table. A few questions: What casters are those? What did you use to attach them to the table? Thanks, Kenric

https://www.amazon.com/Skelang-Leveling-Retractable-Workbench-Capacity/dp/B07V1NTLDP The legs on the Open Builds table are threaded for an M8 or M10 on the bottom plate. I machined up a 1/2" UHMW spacer to center bolt to the table and then through bolt the caster with bolts/lock washers. Worked we…

I’m not sure if there is anything here that adds to what has already been posted here but I have also been thinking about a table design for my second CNC router. A OneFinity Elite Woodworker will replace a smaller CNC. I do bespoke designs for tooling/equipment etc. in Fusion 360. In addition to…

[image] 349iq2345: Cutting area location Spoilboard placement [image] Suckit dust shoe Bristles causing blockage See also: Additionally, the following can be of help: Dust boot overhang UPDATE: Link “ Dust boot overhang ” is broken, here are working links: Dust boot overhang: Front ,…

Just run a cable track across the front of your bench and feed the wires through. It worked fantastically with mine. When I bought a tool setter, I just cut a small slit in the middle to feed that wire through too, so there are no sagging wires at the front.

Would you mind my asking how much making a table like that is costing you? I played around with the idea of using extrusions for mine but the cost was pretty ridiculous. (I’m in Canada and suppliers are limted)

My aluminum extrusion table used ~$350 of extrusions (including cuts, tax and shipping). Here are the pieces I used. The 1M 4040 pieces I used as 4 corner legs and a center leg and ended up cutting them to the height I desired. 5x 4040 - 1M 2x 4040 - 1740mm 8x 2040 - 1700mm Kenric

Whoops! The 2 long 4040 pieces were 1700mm not 1740mm.

Elite Table Builds

Elite Series (Masso & Redline) (Gen 1)

349iq2345 November 16, 2023, 10:12pm 122

UPDATE: Link “Dust boot overhang” is broken, here are working links:

Dust boot overhang: Front, → Rear → Front 2 → Rear 2
- (What is the Best Dust Boot for the Onefinity? )

Topic		Replies	Views
The Table basic Original/PRO Series (Buildbotics) (Gen 1)	145	26119	April 9, 2025
Thoughts on my table design? Machine Setups	24	3484	October 10, 2022
Flip up CNC table Gallery	42	10911	May 11, 2021
CNC platform / table / enclosure Accessories	122	17572	November 3, 2022
Journeyman Table Uncategorized	32	4594	May 24, 2024

Elite Table Builds

Related topics