Updated 1/15/2021 : We’ve identified a bug that was introduced with 1.0.6 Beta. Apparently, when the jerk is raised beyond a certain number (in this case up to 15000) it affects the z probe height, it adds 1.5mm depth when probing for z in xyz probe button. Reducing it back down to 1000 (but staying…

Update was fairly straightforward. After reading other comments about the new jerk settings, I battened down the hatches. It was definitely noticable, especially when using the touch probe, but not as bad when running the program. Here is the result of Carbide Create program using build 514: [PXL_…

@OnefinityCNC I have been communicating with the Buildbotics folks and they just fixed the issue where units default is not reflected on the Control screen. It is in their github as issue #206 and available as a release candidate for testing. Hopefully you will be able to pull this fix into your…

@OnefinityCNC here is what changed: Fixed default units handling. #206 committed 09:59PM - 12 Jan 21 UTC (UTC) [jcoffland] jcoffland +9 -3 …

I reduced my new max jerk from 15000 to 10000 and I like it much better. It tones down the jerk while maintaining a much improved speed for 3D carving.

Just installed firmware ver 1.0.6 BETA… wow! Works great. I figured I would leave the max jerk setting at 15000 for the first couple of test cuts. I’m glad I did. The machine has no problem handling the increased speeds. I will leave it at 15000 for now. I do have it bolted to a 4’x8’ table. I guess…

I had some really weird behaviour using 1.0.6. For reference, I use the the metric vectric post processor on vcarve pro 10.5. See photo below, the installed fence on the left is what I produced once I reverted back to 1.0.5. It behaved flawlessly. But if you look at the two fences on the right and…

I updated my firmware this afternoon. Holy Buckets, those jerk and accel rates are scary fast! I buried the bit during the x,y move on the first carve with the new settings. Do I need to raise my safe z height with these changes? I’ve backed them off to 5000 for now until I figure this out. Thanks

I set my safe z to 75mm. I run my max jerk at 10000. Works for me.

Is the source for the beta available anywhere, I don’t see any branches in the github repo?

Firmware Update 1.0.6 BETA (12/28/2020) (outdated firmware)

Firmware (BB Buildbotics) (Discontinued) Outdated Firmware

OnefinityCNC (Onefinity CNC Official ✅) February 16, 2021, 8:55pm 36

It is not.

20 characters

XYZ probe routine location

Topic		Replies	Views
Firmware Update 1.0.7 BETA (3/11/2021) (Outdated Firmware) Outdated Firmware	36	4598	February 8, 2023
Firmware Update 1.0.6 (2/25/2021) (Outdated Firmware) Outdated Firmware	39	4374	February 8, 2023
Onefinity CNC Firmware 1.3.1 (12/15/23) (X-35/X-50 machines w/ Buildbotics Controller) (Outdated) Outdated Firmware	49	6903	May 24, 2024
Onefinity CNC Firmware 1.6.2 (2/24/25) (X-35/X-50/Pro machines w/ BB Controller) (Outdated Firmware) Outdated Firmware	45	2595	June 20, 2025
Firmware Update 1.0.9 (12/17/21) (Outdated Firmware) Outdated Firmware	73	15897	February 8, 2023

Firmware Update 1.0.6 BETA (12/28/2020) (outdated firmware)

Related topics