Newbie here, sorry if it’s a little long. Please note that english is not my first language so some terminology might not be right. I have an Elite Journeyman purchased a year ago with Masso controler, Masso pendant, touch probe and tool setter. All worked fine under software version 5.07. but be…

Your issue most likely because you didn’t do step 2 and 3 after doing step 1, upgrading the firmware: [image] Elite Series Masso Default Machine Settings Masso Default Configuration FAQ Elite Series Masso Machine Settings: (updated: 11/3/25) Part 1, 2, and 3 …

Default settings can be found here: [image] Elite Series Masso Default Machine Settings Masso Default Configuration FAQ Elite Series Masso Machine Settings: (updated: 11/3/25) Part 1, 2, and 3 must be done in order. :one:Part 1: Firmware <a name="p-61015-before-performing-the-two-steps-below-ensure-the-masso-firmware-is-513-or-later-click-here-to-learn-how-to-update-your-firmware-which-is-different-than-the-below-config-resethttpsdocsmassocomaugetting-started-guidesinstalling-massoloading-software-to-masso-touch-3" class="anchor" href="#p-61015-before-performing-the-two-steps-below-ensure-the-masso-firmware-is-513-or-later-click-here-to-learn-how-to-update-your-firmware-which-is-different-than-the-below-config-resethttpsdocsmassocomaugetting-started-guidesinstalling-massoloading-software-to-masso-touch-3" aria-label="Heading link"> Before performing th…

Thanks, I clearly missed step 2 and 3. I’ll do that as soon as I get back home. Should I go right to step 2 or should I start all over and reinstall 5.10 or 5.13 first?

I’d start over at 5.13 (latest), then do #2 and reboot, then do #3. You’ll have to reset up your tool setter after doing all the above.

So, I reinstalled 5.13 and then adjusted the switches on the motors, rebooted and did 3#. I came back with a Y hard limit alarm (and many inputs in F1 were “high”). Since X and Y were homed, I unplugged the machine to be able to move both axis manually towards the middle of the bed, plugged again …

You probobly blew the screen fuse: [image] Elite Masso Power Supply Fuse Schematics FAQ Official 1F Elite (MASSO) FAQs Elite Fuse Schematic.pdf (203.0 KB) [fuse1] [Elite Power Supply Front] Links to replacement fuses: Variety Kit (slow blow) *Note: 110v …

All fuses are ok :flushed_face:. I think i’m cursed :zany_face:

Hi Gilbert, please try the following steps. Start by fully powering off the MASSO, wait a few seconds, then power it back on. If a proper restart doesn’t do the trick please remove all USB devices such as flash drives and keyboards, a faulty USB device can stop the system from booting properly and …

Thank you all for your help. I found a 2023 thread on Onefinity forum on how to check voltage and my reading is 0. I checked all the fuses again and they are all ok. There is power coming in the box and there is power going to the motors. I will send an email to Masso support and go the “officia…

Hello, I hope this thread is still active. After changing the power box which was defective and causing the black screen issue I’m kinda back to square one. Here’s what I wrote before the black screen issue: “…I reinstalled 5.13 and then adjusted the switches on the motors, rebooted and did 3#. …

[image] How To Clear Motor Alarms On Onefinity Elite Masso. FAQ Official 1F Elite (Gen 1) (MASSO) FAQs If you have issue with alarms on the motor or control screen or axis are counting down but not moving, try the following: Special Notes: This does not apply …

From 5.07 to 5.13 then back to 5.10... all out of wack

Elite Series (Masso & Redline) (Gen 1) Troubleshooting (Elite Series)

OnefinityCNC (Onefinity CNC Official ✅) December 22, 2025, 4:29pm 12

Topic		Replies	Views
Elite Series Masso Default Machine Settings Masso Default Configuration FAQ	0	13049	December 16, 2022
Original Firmware Download and wipe settings Elite Series (Masso & Redline) (Gen 1)	1	243	July 13, 2025
Motor resolution change - manual update? Elite Series (Masso & Redline) (Gen 1)	23	861	November 21, 2024
MASSO Elite firmware version upgrade? Controller (MASSO) Discussion	2	124	January 24, 2026
MASSO Firmware 5.13 out today, anyone else going for it? Controller (MASSO) Discussion	53	2185	May 11, 2026

From 5.07 to 5.13 then back to 5.10... all out of wack

Related topics